The Iron Steel Institute of JapanThe Iron Steel Institute of Japan

日本語
  1. Home
  2. Event
  3. ISIJ Meeting Past Programs
  4. The 154th ISIJ Meeting
  5. General Presentation

Program of the 154th ISIJ Meeting (September 19-21, 2007)
General Presentation Only

Current Advance in Materials and Process, Vol.20, No.4
High Temperature Processes

1 Analysis of size segregation of burden in charging system of blast furnace
M.Kadowaki ···  739
2 Application of DEM against material behavior in blast furnace
T.Nouchi ···  740
3 Influence of scaffolding at throat bricks on blast furnace operation
K.Maeda ···  741
4 Development of new shaped tuyere for high productivity and low reducing agent rate
H.Toyota ···  742
5 Production test of partially reduced iron ore using commercial shaft furnace for DRI
H.Yokoyama ···  743
6 Probing the inner structure of blast furnaces by cosmic-ray muon radiography
S.Matsuzaki ···  744
7 Dissection investigation of blast furnace hearth-Kokura 2BF(2ndcampaign)
T.Inada ···  745
8 Evaluation of effect of micro-particle on granulation
(Study on granulation mechanism of raw materials -2)
S.Kawachi ···  746
9Effect of drum mixer's operating factor on passage time of raw material
(Analysis of raw material motion in drum mixer for sintering process-I-)
M.Hara ···  747
10 Effect of expanding pallet width on increasing production at Kashima No.2 sintering machine
Y.Nakagawa ···  748
11 Surface roughness of iron ore quantitatively measured by laser microscope
M.Nakano ···  749
12 Influence of the slits formation with lump ore in the sintering bed
K.Nushiro ···  750
13 Reduction behavior of mosaic embedding iron ore sinter
Y.Dohi ···  751
14 Effect of dry treatment to granulated sinter mixture on heat generation in sintering bed
(Development of decreasing moisture technique to granulated sinter mixture-2)
M.Matsumura ···  752
15 Effect of ore types and sizes on sintering embedded with large iron ore particle
S.Kasama ···  753
16 Measures for increase in production and improvement of sinter quality at Kokura No.3 sintering plant
A.Sakai ···  754
17 On-line check for the sickness of upper-nozzle of the ladles
T.Tokonami ···  755
18 Improvement of roof refractories for EAF
N.Nukushina ···  756
19 Thermal shock testing of carbon-containing refractories by a direct electrical heating method
S.Honda ···  757
20 Evaluation method of explosive spalling resistance on castable refractories
K.Fujita ···  758
21 Fracture mechanism of alumina-magnesia castable
(Extension of steel making ladle well block life 1)
Y.Tamura ···  759
22 Recycle of refractories in Kimitsu Works
T.Inuzuka ···  760
23 Phosphorus distribution equilibria between liquid iron and tow-liquid CaO-FetO-P2O5 slag saturated with Al2O3
M.Hino ···  761
24 Dissolution of solid oxides into molten slag
N.Maruoka ···  762
25 Reaction between liquid Fe-Cr alloy and MgO refractories
T.Hatakeyama ···  763
26 Performance test results of magnesia-carbon brick with organization stability
S.Umeda ···  764
27 Reoxidation behavior in deoxidation process of molten steel with in-situ produced Mg vapor
R.Takata ···  765
28 Effect of ladle glaze on inclusion formation in a secondary refining of specialty steel
YoungJo Kang ···  766
29 Application of dolomite bricks for VOD ladle
T.Ueno ···  767
30 Development of particle repulsion nozzle for continuous casting
Y.Awajiya ···  768
31 Effect of cooling rate on initial solidification of S45C
H.Mizuno ···  769
32 Cooling rate of solidified shell in the continuous casting mold
M.Hanao ···  770
33 Effect of Ti addition on solidification structure of Ni-based alloy
M.Kubota ···  771
34 Reduction and carburization behavior of hematite-carbon composite pellet
T.Mori ···  772
35 Effect of Al2O3 on reduction behavior of (Fe,Al)2O3 and structure of reduced products
K.Takahashi ···  773
36 Iron and steelmaking of iron ore and charcoal by pulsed electric current sintering
K.Matsumoto ···  774
37 Kinetically analysis of magnetite carbothermal reaction by microwave heating
K.Kodama ···  775
38 In-situ analysis of the effect of the concentration of additive for the reaction of wustite and solid state carbon in TEM
N.Ishikawa ···  776
39 Simulation of coke gasification in a pore by Cellular Automaton method
Y.Kashiwaya ···  777
40 Numerical analysis technology to evaluate coke degradation behavior in blast furnace
Y.Ujisawa ···  778
41 Development of hot stove model
Y.Kimura ···  779
42 (ISIJ Research Promotion Grant)
Magnesium deoxidation equilibrium of molten Fe-Ni alloy
T.Miki ···  780
43 (ISIJ Research Promotion Grant)
Measurement of standard Gibbs energy of formation of cuspidine by transpiration method
R.Kinoshita ···  781
44 Reductive extraction kinetics of titania and iron from an ilmenite by hydrogen
Tan Qiangqiang ···  782
45 Investigation of polyethylene and wood mixture as blast furnace injectant
M.Hasegawa ···  783
46 Phase equilibrium measurement of the Al2O3-CaO-SrO oxide system with laser microscope
T.Kuroki ···  784
47 Mechanism of aluminothermic reduction of chromium oxide
K.Yoshitaka ···  785
48 Mechanical stirring for gas injection refining in iron and steel making1
-Intensification of bubble disintegration
Liu Yan ···  786
49 Mechanical stirring for gas injection refining in iron and steel making2
-Enhancement of absorption of injected gas
Liu Yan ···  787
50 Effects of impeller shape and size on vortex formation condition in offset agitation
S.Sato ···  788
51 Effect of elliptical balls on a swirling liquid jet in a cylindrical vessel
T.Kawayama ···  789
52 Transition of water level in swirling liquid jet in transient period
D.Iguchi ···  790
53 Effect of supporting rod on sediment lifted up by swirling bubbling jet
T.Fujikawa ···  791
54 (Invited Lecture)
Thermophysical property measurements using an electrostatic levitation method
T.Ishikawa ···  792
55 Progress of fast multi-thermophysical-property measurement by electrical-optical hybrid pulse-heating method
H.Watanabe ···  793
56 Density measurement of steel material melts using electromagnetic levitation method
T.Aoyagi ···  794
57 Noncontact modulated laser calorimetry for liquid stainless steel with suppressed convections in a static magnetic field
K.Takahashi ···  795
58 (Invited Lecture)
The study of flow and temperature fields in conducting droplets suspended in a DC/AC combination field
K.A.Pericleous ···  796
59 Dependence of emissivity of liquid iron on temperature and wavelength
K.Sugimori ···  797
60 Surface tension measurement of molten steels by oscillating droplet method combined with phase analysis
S.Ozawa ···  798
61 Temperature dependence of density of Si melt
M.Adachi ···  799
62 Interfacial phenomena between molten iron and prereduced ilmenite
Tan Qiangqiang ···  800
63 Application of thermophysical property database system to thermal and material design
Y.Yamashita ···  801
64 Thermal properties of a single crystal GaN grown by HPVE method
H.Shibata ···  802
65 Fabrication of porous glass using phase separation in multi-component oxide glass containing fundamental components in waste slag
M.Suzuki ···  803
66 Effect of firing temperatures, oxygen partial pressures and glaze compositions on colour tone of celadon glaze
M.Hayashi ···  804
67 Chemical structural analysis of slag using solid-state NMR at high magnetic fields
K.Saito ···  805
68 Viscosity measurement of RE-Mg-Si-O-N (RE=Y, Gd, Nd and La) melts and structural analysis of glasses
S.Sukenaga ···  806
69 Density measurement of molten alkaline earth fluorides by using Archimedean dual sinker method
Y.Sato ···  807
70 Measurements of refractive indices and linear thermal expansion coefficients of alkali and alkaline earth silicate glasses
R.Endo ···  808
71 Determination of viscosity, density and refractive indices for tellurite glass melts
H.Tokunaga ···  809
72 A model for estimating viscosity of molten aluminosilicate
Y.Miyabayashi ···  810
73 Effect of fixed carbon in waste materials on reduction behavior of organic municipal waste materials and iron oxide mixtures
Y.Ueki ···  811
74 Reaction behavior of wood flour added coal composite iron ore hot briquettes in a blast furnace simulator
K.Tanabe ···  812
75 Reaction behavior of potassium added coal composite iron ore hot briquettes at high temperatures under load
N.Hashimoto ···  813
76 Effect of carbon structure on iron carburization behavior
D.Nakatomi ···  814
77 Development of valuable metal recovery technology by using rotary hearth furnace(No.1report)
H.Fujimoto ···  815
78 Development of valuable metal recovery technology by using rotary hearth furnace(No.2report)
H.Sugitatsu ···  816
79 Development of valuable metal recovery technology by using rotary hearth furnace(No.3report)
H.Sugitatsu ···  817
80 Application of DC plasma driven by AC magnetic field to the surface melting of steels
K.Yamamoto ···  818
81 FeO film removal phenomena from iron rod by atmospheric Ar plasma
(The reaction mechanism of the heated object by heat flux from plasma)
K.Kashimura ···  819
82 The pulsative electromagnetic casting technique for slab casting
M.Tani ···  820
83 Production of uniformly sized droplet from liquid metal jet by electromagnetic force
S.Shimasaki ···  821
84 Characteristic of entrainment of low density particle from free surface of molten metal under double-axis electromagnetic stirring
S.Nakagawa ···  822
85 (ISIJ Research Promotion Grant)
Development of desiliconization in hot metal treatment by gas injection of low oxygen potential
T.Aihara ···  823
86 Suppression of dephosphorization slag foaming by coke powder top blowing
M.Miyata ···  824
87 Decarburization and slag formation model for electric arc furnace
H.Matsuura ···  825
88 Application and jet behaviors of an innovated double-parameter oxygen lance in BOF of Bao-Steel
Xiao Yang ···  826
89 Contribution of heat transfer from top blowing jet to metal bath on transport of heat generated by post combustion in BOF
T.Suzuki ···  827
90 Improvement of heat size in Kakogawa Works
T.Inaba ···  828
91 Effect of nozzle twisted in the jet penetration using physical model of BOF converter
Breno Totti Maia ···  829
92 Effect of top slag conditions on the rate of hot metal desulphurization
S.Mukawa ···  830
93 Desulfurization of liquid iron by solid CaO with porous structure
M.Ohmachi ···  831
94 Modelling of the reaction between calcium ferrite and molten Fe-P-Si alloy
M.Terasawa ···  832
95 FeO activity in heterogeneous slag used for industrial hot metal dephosphorization
Y.Uchida ···  833
96 Behavior of phosphorous partition from liquid slag to dicalcium silicate
S.Kitamura ···  834
97 Microscopic reaction mechanism between solid CaO and FeOx-CaO-SiO2-P2O5slag
R.Saito ···  835
98 Evaluation on the residual slag recycling after phosphorus recovery from steelmaking slag
H.Kubo ···  836
99 Evaluations of viscosity and crystallization behavior of CaO-SiO2 based multi-phase fluxes
S.Yoshimura ···  837
101 Thermal conductivity measurements and prediction for liquid containing solid dispersion phase
N.Tsuchida ···  838
102 Flow simulation of the molten slag falling onto the iron bath
H.Nijo ···  839
102 (ISIJ Research Promotion Grant)
Effect of the urea addition as aqueous solution to the high temperature waste gas on the decrease in the dioxins concentration
E.Kasai ···  840
103 Effects of reduction conditions on the strength of direct reduced iron
Young Seok, LEE ···  841
104 Promotion of calcite precipitation on surface of Ca(OH)2 powder using vibrating treatment
M.Takeuchi ···  842
105 Suppression of sea water color change to muddy using calcite precipitation treated Ca(OH)2 powder
M.Takeuchi ···  843
106 Dissolution behavior of chromium from MgO�Cr2O3 and FeO�Cr2O3 phases into water
S.Ikeno ···  844
107 Fixation of carbon dioxide using mechanically milled steelmaking slag
E.Yamasue ···  845
108 Dissolution control of fluorine from electric furnace reducing slag into water
Y.Nagaike ···  846
109 Emission behavior of hexachlorobenzene from electric arc furnace dust for steel making
M.Shimura ···  847
110 Effect of crystalline morphology on heat transfer through mold flux film
K.Matsuo ···  848
111 Design of mold flux for slow cooling based upon morphology control of cuspidine crystals
H.Nakada ···  849
112 Mold flux for continuous casting of aluminum-alloyed steel slabs
M.Hanao ···  850
113 Effect of initial solidification morphology on hot cracking sensitivity in Ti-added HSLA steel
T.Mochida ···  851
114 Prevention of crack formation on blooming of several kinds of high N content steel in CC-HCR process
K.Isobe ···  852
115 Deformation behavior of ultra low carbon steel at high temperature
K.Fuchigami ···  853
116 Influence of specimen gathering position on hot ductility of the Cu and Ni containing low carbon steel
Donggyu Kim ···  854
117 Quality improvements of bloom with new continuous caster
Y.Yoshida ···  855
118 Reoxidation of molten steel by CaO-SiO2-Al2O3 slag
H.Yamamura ···  856
119 Stability of deoxidation products in Si-Mn deoxideized stainless steel
H.Shibata ···  857
120 Effect of chemical composition on MnS morphology of low-carbon resulfurized free cutting steel
K.Sakamoto ···  858
121 Reducing inclusions using the pressure elevating and reducing method in RH degasser
T.Murai ···  859
122 The investigation of generating mechanism and removal method of inclusions in tundish
Min Oh Suk ···  860
123 Observation of inclusion evolution during Al and Ti addition to molten iron
H.Matsuura ···  861
124 Refining reaction analysis in high O and S steel
A.Okayama ···  862
125 Behavior of slag entrapment in gas-stirred ladles
H.Matsumoto ···  863
126 Inclusions behavior in Mn-Si-Mg complex deoxidation process of molten steel
R.Irizato ···  864
127 Behavior of inclusions in deoxidation process of molten steel by titanium
K.Okumura ···  865
128 Effect of corner chamfer on fluid flow pattern in mould
M.Miyazaki ···  866
129 Suppression of the asymmetric flow by current control of the in-mold electromagnetic stirring
M.Morishita ···  867
130 Numerical method for macro-segregation prediction
T.Sawada ···  868
131 Effect of macrosegregation on porosity formation of 13% Cr steel under pressurized atmosphere
F.Takahashi ···  869
132 Crack increase in combustion chamber wall of coke oven
S.Ishikawa ···  870
133 Consideration of coke oven wall carbon adhesion with PCOM
T.Yoshihara ···  871
134 Development of the combustion chamber observation device (2)
H.Kinoshita ···  872
135 Environmental measures of coking furnace in Chiba Works
S.Kikuchi ···  873
136 Construction and operation of Mitsui Mining No.1 coke dry quencher and coal moisture control equipment
T.Takatsugi ···  874
137 Depression of dusting and carbon deposition by compacting coal fine
(Development of carbon deposition control technology in the coke oven-11)
T.Nakagawa ···  875
138 Effect of coking conditions on clearance between coke oven wall and coke cake
T.Yamamoto ···  876
139 Effect of oven width narrowing on coke cake pushing force
S.Aizawa ···  877
140 Development of a detector for gas leakage form coke oven doors (II)
H.Yamashita ···  878
141 Smoothing of ceramic welding surface by coating material
K.Kojima ···  879
142 Elucidation of desulfurizing tower blockage factor
M.Inukai ···  880


Current Advance in Materials and Process, Vol.20, No.4


Social Engineering on Iron and Steel Industry/High Temperature Process

143 (Invited Lecture)
Preparation of porous material from molten slag by hydrothermal reaction for humidity control and VOC removal
M.Moriyama ···  882
144 Immobilization of Cr(VI) in aqueous solution by hydrothermal treatment with BF slag
Soon-Jae Tae ···  883
145 Synthesis of layered Co oxide thermoelectric materials by citric acid complex and hydrothermal hot-pressing processes and investigation of its thermoelectric properties
S.Katsuyama ···  884
146 Invention of foaming glass material utilizing hydrothermal treatment
S.Sato ···  885
147 Fabrication of slag or glass blocks by using hydrothermal reaction
T.Tanaka ···  886


Social Engineering on Iron and Steel Industry
148 Relation between concepts of ergonomics and holonomy in education
E..Kanoshima ···  887
149 Relation between concepts of risk assessment, risk management and holonomy in education
E..Kanoshima ···  888
150 Standardization in holonomical system application
T.Noda ···  889
151 Changes in carbon content of materials of the Japanese sword under traditional forging process
N.Sasaki ···  890
152 Formed zuku by the steelmaking process using modified tatara furnace
M.Hokahara ···  891


Current Advance in Materials and Process, Vol.20, No.4


Environmental and Energy Technology
377 Development of waste tire recycling system using steel making process
H.Nyuu ···  913
378Development of binder using waste plastics
M.Asanuma ···  914
379 Development of modified asphalt using waste plastics as a modifier
M.Kajioka ···  915
380 Efficient sonochemical degradation of hexachlorobenzene in a model sediment
H.Choshi ···  916
381 Role of unburned carbon in the distribution of the fluorine in coal to fly ash
N.Tsubouchi ···  917
382 Mixture source and behavior of Co in steelmaking process
Technology to produce low activation steel(2)
S.Kitamura ···  918
383 (ISIJ Research Promotion Grant)
Substance flow analysis of manganese associated with iron and steel flow in Japan
K.Nakajima ···  919
384 Absorption of CO2 in reducing slag of electric arc furnace under wet grinding by vibration ball mill
R.Sato ···  920
385 Coproduction of hydrogen and zeolite-A or -X from waste silicon and aluminum
N.Okinaka ···  921
386 LCA for hydrogen production by using aluminum dross and metal sludge
K.Yokoyama ···  922
387 Vapor/liquid infiltration of tar into lean ores
Y.Hata ···  923
388 Development of the hydrogen production system for recovery of waste heat
(Intermediate temperature steam electrolysis cell using LaGaO3 based solid oxide electrolyte)
T.Kanno ···  924
389 Effect of slag catalysts for production of the biodiesel oil
K.Toishi ···  925
390 Catalytic ability of slag surface on the methane decomposition reaction and phenomena during a bubbling of methane into molten slag
Y.Kashiwaya ···  926


Current Advance in Materials and Process, Vol.20, No.5


Instrumentation, Control and System Engineering
153 Visualization and evaluation of fatigue damage in steels using laser
A.Kato ···  950
154 Measurement of core loss in silicon steel sheet by single sheet testers
T.Tamaki ···  951
155 Non-linear separation of characteristic values of surface defects by the EM algorithm
A.Kazama ···  952
156 New process computer system of coal
E.Nagayama ···  953
157 Development of dynamic control model in BOF using mathematical optimization
K.Iwamura ···  954
158 Development of Just-In-Time modeling in BOF blowing control
H.Mizuno ···  955
159 Quantification of qualitative quality information and estimating method of operating condition for improving product quality
S.Nakagawa ···  956
160 Optimum scheduling system for raw materials shipment at discharging ports
H.Kobayashi ···  957
161 Prediction of steel product shipment quantities by case based method
K.Wajima ···  958
162 Agent based acquisition of gain tuning rules for hot strip looper controller
Y.Abe ···  959
163 Development and application of middleware to the process automation in iron and steel making
N.Sumida ···  960


Current Advance in Materials and Process, Vol.20, No.5


Processing for Quality Products
164 Influence of rolling condition on deformation behavior of surface micro-defects in steel bar rolling
S.Nagano ···  982
165 Experimental analysis of exfoliating stress between metal and scale at high temperature(2)
H.Kushida ···  983
166 Effect of nickel on scale formation during high temperature oxidation of steels containing nickel
Y.Kondo ···  984
167 Basic structure of NSC intelligent mill
(Development of NSC intelligent mill-1)
S.Ogawa ···  985
168 Verification of basic characteristics in pilot NSC intelligent mill
(Development of NSC intelligent mill-2)
T.Shiraishi ···  986
169 Introduction of endless hot rolling at Pohang Works of POSCO
Jongsub Lee ···  987
170 Characteristics of high reduction and minimum thickness in stainless steel foil rolling
J.Tateno ···  988
171 Prediction model of strip temperature for stainless cold rolling
N.Fukuda ···  989
172 (ISIJ Research Promotion Grant)
Microstructural evolution during friction stir welding of ultrahigh carbon steel with microduplex structure
Y.Sato ···  990
173 Specification of high-speed large-reduction forging machine for hot rolling process
(Grain refinement by large reduction forging technology -9)
M.Miyake ···  991
174 Numerical simulation of microstructure evolution on multi-bending process
(Grain refining investigation by complex rolling / bending multiple accumulation process-7)
Y.Matsubara ···  992
175 Characteristics of liquid colloidal lubricants with solid powder lubricant and inorganic compound-6
J.Ikeda ···  993
176 Effect of rolling speed on coefficient of friction in hot rolling
Y.Nakata ···  994
177 Three-dimensional numerical study of a free surface liquid jet impinging on a hot surface
H.Fujimoto ···  995
178 Improvement in surface gloss of Ni plated steel wire in drawing process
M.Nakano ···  996
179 Improvement of draw ability of ferrous shape-memory alloy wire
T.Sato ···  997
180 Use of a void model for the simulation of inner fracture defect in drawing of high-carbon-steel wire rods
K.Komori ···  998
181 Development of compact stream line method with multiple forming stages
(Development of energy-saving reduction-of-labor type FEA system of material forming-6)
T.Yoshida ···  999
182 (Invited Lecture)
Influence of micro structure on surface integrity in ultra-precision cutting
K.Okuda ···  1000
183 Consideration of machined surface formation mechanism in structural steels with quick stop test
M.Hashimura ···  1001
184 Effect of hardness of steels on burr shape formed around drill holes
K.Miyanishi ···  1002
185 Machinability of drilling deep hole by MQL(Minimum quantity lubrication)
T.Kajino ···  1003
186 Effect of sulfide inclusions on surface roughness in free cutting low carbon steel
T.Murakami ···  1004
187 Effect of lead inclusion on chip formation of carbon steels for machine structural uses
K.Watari ···  1005
188 (ISIJ Research Promotion Grant)
Measurement of hydraulic pressure distribution in sheet hydroforming
T.Hama ···  1006
189 Dimensional accuracy in roll forming of high-tensile strength steel sheets
(1st report Hat-shaped bending test in roll forming)
R.Ishihara ···  1007
190 Butt joining of sheet by microshot peening
M.Fukunaga ···  1008
191 Development of continuous rolling technology in 4 inch ERW mill with 4 roll type reducing mill
Y.Takemura ···  1009
192 Influence of forming conditions on thickness change in spinning forming of welded steel pipe
(Deformation in spinning forming of welded steel pipe-2)
A.Ando ···  1010
193 Simulation of microstructural formation on the process of solid state and liquid phase sintering
H.Matsubara ···  1011
194 Simulation of deformation behavior on solid state and liquid phase sintering
H.Matsubara ···  1012
195 Coupled simulation of volume, grain-boundary and surface diffusion in sintering
K.Shinagawa ···  1013
196 Direct laser sintering of titanium powder
H.Miura ···  1014
197 An investigation of the densification process of iron powder during warm compaction with die wall lubrication
Y.Ozaki ···  1015
198 (Invited Lecture)
Slip of metallic powders for high-speed centrifugal compaction process
H.Suzuki ···  1016
199 Rotating bending fatigue strength of sintered and carburized compacts made of molybdenum hybrid-alloyed steel powder
S.Unami ···  1017
200 Mechanical properties of Fe-Al-C perovskite-type alloy fabricated by powder metallurgical process
K.Isonishi ···  1018
201 Effects of sintering conditions on the mechanical properties of sintered molybdenum
T.Kadokura ···  1019
202 (Invited Lecture)
Microstructural refinement and thermoelectric properties of Heusler-type Fe2VAl alloy
M.Mikami ···  1020
203 (Invited Lecture)
Fabrication and properties of nano-structured ceramics by powder metallurgy process
T.Ueno ···  1021
204 Thermal property and interface of carbon nanotube/copper composite
S.Yamanaka ···  1022
205 (Invited Lecture)
Role of pores in cutting of resin impregnated sintered iron
K.Okimoto ···  1023
206 Dynamic explicit FEA of dimensional defect at sheet end in roller leveling of thick plate
M.Yamashita ···  1024
207 Deformation behavior of initial curvature in roller leveling process
M.Enomoto ···  1025
208 Development of residual stress analysis model in roller leveling considering Bauschinger effect
T.Kubo ···  1026
209 Robust tension leveling process design by means of stochastic optimization
M.Shigaki ···  1027
210 Finite element analysis on roller leveling process of equal leg angle
K.Hayakawa ···  1028
211 Analysis of roller straightening of wire by FEM
T.Sugiyama ···  1029
212 Improvement of roundness of steel tube
H.Yoshimura ···  1030


Current Advance in Materials and Process, Vol.20, No.6


Microstructure and Properties of Materials
213 Microstructural change during hot band annealing in type 430 stainless steel
H.Ota ···  1160
214 Effect of warm press forming on the deep drawability of ferritic stainless steel
Y.Ozaki ···  1161
215 Effect of FeTiP precipitation behavior on corrosion resistance of SUH409L stainless steel in sulfuric acid
S.Teraoka ···  1162
216 Thermal fatigue properties of Cu and Nb bearing ferritic stainless steels
T.Tomita ···  1163
217 Effects of Ti addition on surface oxide scales of IF-type ferritic stainless steels at 873K
M.Hatano ···  1164
218 Effect of deformation temperature and strain on α' and ε phase formation in SUS304
Y.Adachi ···  1165
219 The transcription property of the die shape in the micro forging of SUS304 with hyperfine crystal grain
M.Katoh ···  1166
220 Influence of textures on work hardening behavior in SUS316L
K.Kimura ···  1167
221 High temperature steam oxidation of Si bearing austenitic stainless steels
(High temperature steam oxidation of stainless steels -1)
Y.Nishida ···  1168
222 Effects of S and P on pitting potential in Cr-Mn-Ni austenitic stainless steels
T.Hamada ···  1169
223 Hardening mechanism in a high nitrogen bearing martensitic stainless steel studied by small angle scattering
M.Ojima ···  1170
224 Examination of an optimum condition for fabricating high nitrogen stainless steel by metal injection molding method
Y.Aoyama ···  1171
225 Influence of prior spherical annealing on quenching and tempering properties for a high nitrogen martensitic stainless steel
S.Ueta ···  1172
226 Processing and evaluation of PM stainless steel containing high nitrogen using low-temperature nitrided powder
D.Yokoi ···  1173
227 The effect of warm forming on powdering of GA steel sheet
T.Nakamura ···  1174
228 The effect of phosphorus in steel on galvannealing behavior
S.Yamanaka ···  1175
229 Effect of bath temperature on initial reaction between liquid Zn and Si containing steel sheets
T.Yasui ···  1176
230 Development of ultra-high strength galvannealed steel sheets with tensile strength of 980MPa
K.Matsumura ···  1177
231 Aluminum powder eutectic coating for steels
H.Nakano ···  1178
232(ISIJ Research Promotion Grant)Technical module for erosion-corrosion of carbon steel
K.Ito···  1179
233 Corrosion resistance of hot dip Zn-Al-Mg-Si coated steel under atmospheric environment
N.Shimoda ···  1180
234 Corrosion prevention of 55%Al-Zn coated steels by conducting polypyrrole film containing molybdate ion
H.Ryu ···  1181
235 Effect of coating composition and coating mass of chemical conversion treatment on characteristics of hot-dip aluminized steel sheet
M.Yamamoto ···  1182
236 Corrosion resistance of chromium-free PCM on outdoor exposure test 2
Y.Kawamura ···  1183
237 Influence of boundary conditions on damping properties of vibration damping steel sheets
N.Kadowaki ···  1184
238 Formation of antibacterial tin-silver films through heat-treatment alloying process
D.Kuroda ···  1185
239 Formation of tin-palladium films by heat-treatment alloying process and its surface properties
H.Kanematsu ···  1186
240 Reduction of contact electric resistance of stainless steel by carbon particle thermal diffusion treatment
Y.Morita ···  1187
241 (ISIJ Research Promotion Grant)
Mechanism of irradiation resistance in oxide dispersion strengthening steels
A.Kimura ···  1188
242 Particle size in martensitic steel measured by TEM and XRD
M.Tamura ···  1189
243 Three-dimensional electron tomography for high-Cr ferritic heat-resistant steels bearing V and Nb
M.Mitsuhara ···  1190
244 Changes in hydrogen desorption characteristics of Mod.9Cr-1Mo steel due to creep
S.Komazaki ···  1191
245 (ISIJ Research Promotion Grant)
Effect of dissolution hydrogen and S on high temperature steam oxidation in high-Cr steels
Y.Murata ···  1192
246 Formation of Cr2O3 scale on 9Cr steel by pre-oxidation treatment and its long-term stability during subsequent steam oxidation
H.Okubo ···  1193
247 Effect of heat treatment on high temperature tensile property and toughness in 9Cr-W-Mo-V-Nb steel
S.Obara ···  1194
248 Influence of variation in precipitate size on creep of 9%Cr-1%MoVNb steel
Anoop Kabadwal ···  1195
249 Effect of Z phase on creep properties of 9-12Cr ferritic heat resistant steels -2
M.Yoshizawa ···  1196
250 Effect of Cr on the change of MX and M2X in high Cr ferritic heat resistant steels
K.Miki ···  1197
251 Precipitation behavior and growth rate of high Cr ferritic heat resistant steels
K.Yamashita ···  1198
252 Effect of cobalt on microstructure and creep deformation behavior of tempered martensitic 9Cr steel for USC power plant
Libor Helis ···  1199
253 Beneficial effect of Re on the long-term creep strength of high Cr ferritic heat resistant steels
R.Hashizume ···  1200
254 (ISIJ Research Promotion Grant)
Detection of breakdown of creep strength in advanced high Cr ferritic steels by hardness measurement of aged structures at high temperature
Hassan Ghassemi Armaki ···  1201
255 Influence of stress on creep strength property of creep strength enhanced ferritic steels
K.Kimura ···  1202
256 Metallographic atlas of 1Cr-1Mo-0.25V turbine rotor steel
H.Kushima ···  1203
257 Properties of high strength 1.25Cr-0.4Mo-Nb-V steel at elevated temperatures-3-
(Effect of trace elements on creep ductility of a high strength low alloy heat resistant steel)
K.Miyata ···  1204
258 Properties of high strength 1.25Cr-0.4Mo-Nb-V steel at elevated temperatures-4-
(Evaluation of the developed tubes in practical boiler for a long time field exposure test)
T.Nakashima ···  1205
259 A study of fire resistant steels from the view point of an improvement of creep properties
S.Muneki ···  1206
260 Effect of bainite transformation and partial quenching on martensite start temperature(Ms)
H.Kawata ···  1207
261 Bainite transformation behavior at austenite/ferrite grain boundary
M.Azuma ···  1208
262 Effect of heat treatment condition on γ/α transformation ratio in medium carbon steel
S.Teramoto ···  1209
263 Effect of ausforming on crystallographic orientation of reversed austenite formed within lath martensitic structure
N.Nakada ···  1210
264 In-situ observation of γ��α transformation in steel by laser scanning confocal microscopy
N.Oku ···  1211
265 Effect of B and Mo addition on transformation behavior of low carbon steel
K.Takahashi ···  1212
266 Particle size and atomic concentration ratio of composite carbides in ferrite matrix
T.Ariga ···  1213
267 Microstructure and strength properties in Cu particle dispersion pearlitic steel
Y.Takanaga ···  1214
268 Multiple precipitation behavior of hard carbide and soft Cu particles in martensitic steel
M.Murakami ···  1215
269 Microstructure of plasma-nitrided high carbon martensitic steels
S.Kitsuya ···  1216
270 Prediction of austenite textures prior to transformation in hot rolled steel sheets by MODF(Part 2)
T.Tomida ···  1217
271 Effect of tempering temperature on the development of the deformation structure in the lath martensite
S.Morito ···  1218
272 Enlargement of specimens in ultrasonic fatigue testing
Y.Furuya ···  1219
273 Giga-cycle fatigue properties of induction hardened S40C carbon steels
T.Abe ···  1220
274 Gigacycle fatigue properties of hydrogen charged high strength steels
H.Hirukawa ···  1221
275 The effect of hydrogen on fatigue properties for work-hardened SUS316L austenitic stainless steel
E.Takeuchi ···  1222
276 The evaluation of low-cycle fatigue life for notched specimen of high strength steel
T.Makino ···  1223
277 Effects of fine shot bombing on high-cycle fatigue properties for 3 mass%Si steel sheets
K.Ohno ···  1224
278 Fatigue properties of titanium alloy
N.Nagashima ···  1225
279 Effects of η phase precipitation to high temperature ductility of Ni base superalloy for gas turbine combustor parts
S.Imano ···  1226
280 Influence of tungsten and molybdenum on microstructure of nickel-based superalloys with low thermal expansion
S.Kurata ···  1227
281 Analysis of creep damage in high temperature metals with crystal orientation distribution
R.Takaku ···  1228
282 Creep resistance of single crystal nickel-based superalloy,CMSX-4,at1073K
Y.Hayashi ···  1229
283 Dislocation substructures of single crystal nickel-based superalloy,CMSX-4,crept in temperature range of 1073 to 1223K at 600MPa
Y.Hayashi ···  1230
284 Change in dislocation substructures at γ/γ' interfaces of single crystal nickel-based superalloy, CMSX-4, interrupted up to 5% creep strain at 1273K-400MPa with simple aging
N.Miura ···  1231
285 Slip system during creep deformation in γ single phase Ni-20Cr single crystal
F.Harada ···  1232
286 An improvement of creep properties of carbon and nitrogen free Fe-12Ni-9Co-5Mo-5Cr martensitic alloys
S.Muneki ···  1233
287 Time-temperature-precipitation diagram of HK40 casting steel
M.Murata ···  1234
288 Precipitation of Fe2Nb Laves phase in cold worked carbon free Fe-20Cr-30Ni-2Nb austenitic heat resistant steel
K.Yoshimura ···  1235
289 Microstructure and creep properties of a carbon free Fe-20Cr-30Ni-2Nb austenitic heat resistant steel
N.Hashizume ···  1236
290 Development of Fe-Ni base austenitic alloys for piping in 700oC USC power plants
H.Okada ···  1237
291 The effect of peak strain dwell on Creep-Fatigue for the candidate materials of 700oC-USC boiler
K.Kubushiro ···  1238
292 Comparison among macro segregation tendencies of candidate alloys for A-USC
K.Kajikawa ···  1239
293 Recrystallization and grain growth behavior of Ni-Fe base superalloy FENIX-700 for A-USC turbine rotor materials
S.Ohsaki ···  1240
294 Creep strength of solution treated high strength Ni-based alloy (Ni-20Cr-10Mo-1Al-2Ti)
Gang Bao ···  1241
295 (ISIJ Research Promotion Grant)
Electrochemical properties of stainless steel in cooling water environments of nuclear power plants
N.Hara ···  1242
296 The effects of alloying elements on the corrosion properties of sulphuric acid dew-point corrosion resistant steel for the fossil power industry
Kee-Jo Jeong ···  1243
297 Influence of organics on electrochemical corrosion behavior of boiler tube steels
Hao-Feng Zhang ···  1244
298 Effect of chloride ion on the atmospheric corrosion of steel
T.Kamimura ···  1245
299 Assessment of coated steel sheet surfaces in relation to appearance after painting
Young-Min Choi ···  1246
300 Atomic/electronic structure of honeycomb-like patterns on hexagonal-prism Fe-whisker single crystal {110} surface
T.Yamada ···  1247
301 Local atomic phase transition on rectangle-prism Fe-whisker single crystal {100} surface
H.Tamura ···  1248
302 (ISIJ Research Promotion Grant)
Accelerated evolution of ultrafine grains by coarse particles during multi-directional forging of Ni-Fe alloy
H.Miura ···  1249
303 Effect of initial microstructure on behavior of dynamic recrystallization in an ultra low carbon steel
Joo-Hee Kang ···  1250
304 The effect of coiling temperature on the recrystallization texture of Ti added low carbon steel sheet
N.Sugiura ···  1251
305 Texture change after α-γ-α transformation in high strength low carbon cold-rolled steel sheets
H.Saito ···  1252
306 Pole figures determined by a neutron diffraction integrated intensity method for an IF steel
Pingguang XU ···  1253
307 A model for predicting static recrystallization rate in austenite measured by torsional double hit test
Hyun Jin Kim ···  1254
308 Periodic lattice rotation in microshear bands in bcc and fcc alloys
Dorothee DORNER ···  1255
309 Precipitation behavior of copper sulfide in low carbon steel
Y.Iwata ···  1256
310 Investigation of ferrite transformation behaviors from steel-oxide interface
K.Kasai ···  1257
311 Molecular dynamics of melting and nucleation process of iron cluster
Y.Shibuta ···  1258
312 Simulation of separation of hydrogen desorption peak for grain boundary
K.Ebihara ···  1259
313 Molecular dynamics study of grain boundary energy of iron
S.Takamoto ···  1260
314 Thermodynamic analysis of the Fe-Zr-B ternary phase diagram
K.Terashima ···  1261
315 Thermodynamic analysis of the Fe-Nb-B ternary phase diagram
Y.Nakama ···  1262
316 Thermodynamic analysis of the Fe-Cr-B ternary phase diagram
K.Yamada ···  1263
317 Thermodynamic analysis of phase equilibria in the Fe-Co-B ternary system
T.Tokunaga ···  1264
318 Thermodynamic analysis of the Fe-Cr-Ni-B quaternary phase diagram
K.Yoshitomi ···  1265
319 Influence of alloying element on TiN dispersion state of weld heat affected zone
H.Takaoka ···  1266
320 Development of high deformability X100 linepipe by microstructure control for bainite and MA
M.Okatsu ···  1267
321 Development of ultra-high strength linepipes with dual-phase microstructure for high strain application
N.Ishikawa ···  1268
322 Conditions of separation occurrence for low carbon high strength line pipe steels
T.Hara ···  1269
323 Three dimensional simulation of polycrystalline cleavage crack propagation in steel
K.Sugimoto ···  1270
324 Detection of hydrogen trapped by nano-scale carbide by small-angle neutron scattering
M.Ohnuma ···  1271
325 Hydrogen trapping versus stress inside and outside TiC precipitates in steels
M.Enomoto ···  1272
326 Peak separation of hydrogen trapped at various lattice defects by thermal desorption spectrometry
K.Fujita ···  1273
327 Hydrogen evolution behavior of pure iron during elastic and plastic deformation
H.Shoda ···  1274
328 Effect of hydrogen and strain on lattice defect formation and delayed fracture of high-strength steel
H.Saitou ···  1275
329 Effect of hydrogen on delayed fracture mode of high strength steel
A.Endo ···  1276
330 Effect of plastic strain on delayed fracture characteristics
N.Shimuta ···  1277
331 Effect of cold drawing on mechanical properties of carbon steel for machine structural use
N.Tsunekage ···  1278
332 Effect of microstructure on thermal fatigue property of hot-die steel
Y.Ito ···  1279
333 Achieved high strength-plasticity level of Si-Cr spring steel
Jiang YIN ···  1280
334 Reduction of copper sulfide in Ti-IF steel by residual level of copper during long-minute-annealing in α region
Y.Ishiguro ···  1281
335 Effect of carbon and nitrogen on Hall-Petch coefficient in ferritic steels
K.Takeda ···  1282
336 Yield strength and ferrite grain diameter of Cr-bearing extra low carbon steel sheet
Y.Funakawa ···  1283
337 Effect of molybdenum on mechanical properties of C-Si-Cr-Mo steel with Micro Duplex (MD)structure
R.Ueji ···  1284
338 Effect of coiling temperature on mechanical properties and microstructures for dual phase type high strength sheet steels
T.Matsumoto ···  1285
339 Influence of heat treatment on the mechanical properties of cold-rolled low-Si TRIP-GA sheet steel
Won-Bae Kim ···  1286
340 Monte Carlo simulation for competing behaviors between recrystallization and transformation in cold-rolled dual phase steels
K.Okuda ···  1287
341 Influence of microstructures on strain age hardening behavior of multi phase steel sheets
S.Kaneko ···  1288
342 Effect of bake hardening treatment on tensile properties at high strain rate
(Study on microstructure and deformation behavior at high strain rate for cold-rolled steels with good formability-2)
T.Iwatsu ···  1289
343 Stretch-flangeability of ultra high-strength low alloy TRIP-aided sheet steels with mixed structure matrix of bainitic ferrite and martensite
M.Murata ···  1290
344 Nanohardness of fine martensite in ultra high strength steels
K.Kawamura ···  1291
345 Evaluation of hole expanding ratio of 780MPa grade high strength steels with nano indentation technique
S.Takagi ···  1292
346 Effect of micro-voids and pre-strain on hole-expanding ratio
N.Kariya ···  1293
347 Development of automobile parts with hot-dip coated ultra high strength steel sheets using hot stamping
Hee-Joong IM ···  1294
348 The effect of heating conditions on decarburization in hot stamping process
K.Hayashi ···  1295
349 Effect of welding speed on hardness and microstructure of hot-stamped laser weldmetals
T.Nishibata ···  1296
350 (ISIJ Research Promotion Grant)
Relationship between initial dislocation density and yielding behavior in ultralow carbon martensitic steel
H.Matsubayashi ···  1297
351 Stress-strain relations for ferrite-cementite steels with a wide range of ferrite grain size
N.Tsuchida ···  1298
352 Tensile property of ultrafine grained ferritic steel produced by HPT straining
Y.Todaka ···  1299
353 Multi-scaled deformation behavior for martensite steel by EBSD
S.Morooka ···  1300
354 Multi-scaled deformation behavior for pearlite steel by EBSD
S.Morooka ···  1301
355 Effect of Cr precipitates diameter on elongation of high Cr steel
M.Aramaki ···  1302
356 (ISIJ Research Promotion Grant)
Effect of heat treatment on pseudoelastic behavior of Fe3Ga single crystals
H.Yasuda ···  1303
357 Dissolution of manganese sulfide and grain growth behavior during isothermal annealing of 3%-silicon steels
M.Muraki ···  1304
358 Effect of nitriding process on the recrystallization behaviors and magnetic properties of grain oriented electrical steel
Chun-Chih Liao ···  1305
359 Abnormal grain growth simulation by using Capillary Driven Surface Tracking model
H.Homma ···  1306
360 The effect of dislocations in grains on texture formation in SIBM
(Texture formation during SIBM in electrical steel sheets4)
K.Murakami ···  1307
361 Effect of properties of non-oriented electrical steel sheet on motor efficiency of interior-permanent-magnet synchronous motor
H.Nitomi ···  1308


Current Advance in Materials and Process, Vol.20, No.6


Process Evaluation and Material Characterization
362 (ISIJ Research Promotion Grant)
Development of helium glow discharge optical emission spectrometry aiming at rapid trace analysis of gas impurities in steel samples
H.Matsuta ···  1348
363 Development of on-site quantitative analysis of wax on steel sheets
K.Hanada ···  1349
364 Anthracene and phenanthrene gas emission monitoring from coal pyrolysis reaction by Jet-REMPI/TOFMS technique
M.Aimoto ···  1350
365 Dehydration method of the iron ore that includes much combined water
Y.Fujioka ···  1351
366 Measurement of texture and residual stress distribution by neutron diffraction
T.Suzuki ···  1352
367 Estimation of rolling contact fatigue life derived from distribution of non-metallic inclusions-1
K.Yagita ···  1353
368 Estimation of rolling contact fatigue life derived from distribution of non-metallic inclusions-2
K.Yagita ···  1354
369 Development of quantitative analysis for Laves phase in the ferritic stainless steels
M.Inose ···  1355
370 (ISIJ Research Promotion Grant)
Admicellar separation and subsequent high-performance liquid chromatography for the spectrophotometric determination of phosphorus in high-purity iron
T.Kikai ···  1356
371 (ISIJ Research Promotion Grant)Removal of an iron matrix by coacervation of a nonionic surfactant
Y.Sakane ···  1357
372 Effects of cobalt element on microstructures of TRIP-assisted steels
Eunji Yu ···  1358
373 Effects of Cu on mechanical properties and microstructures in TRIP steel
Youngchul Han ···  1359
374 Establishment and problem of the observing system for boron in steels by alpha-particle track etching method using pneumatic tube of JAEA
K.Asakura ···  1360
375 Surface structural analysis of single-crystalline wustite(001) using STM and LEED
Y.Masaki ···  1361
376 Analysis of amorphous structure of biaxially oriented PET film for laminated steel
J.Kitagawa ···  1362

previous page