Program of the 150th ISIJ Meeting (September 28-30, 2005)
General Presentation Only
High Temperature Processes
1 (ISIJ Research Promotion Grant)
Analysis of structure of liquid and viscous flow near solid-liquid interface using molecular dynamics M.Suzuki
2 Wettability between ironmaking slag and cokes in blast furnace K.Saito
3 Development of thermal transport properties measurements of molten metals by a levitation technique coupled with a static magnetic field I.Minato
4 Viscosity of Fe-C binary melt Y.Sato
5 Evaluation of viscosity of molten slag by using neural network computation T.Tanaka
6 Evaluation of viscosity of mold flux by using neural network computation M.Hanao
7 Development of high speed casting technology in the No.2 CCM at Kakogawa works K.Sumida
8 Labor-saving of Keihin 1CCM S.Hatori
9 Investigation of secondary cooling nozzle clogging No.4CC-2STR Y.Yamamoto
10 Improvement of sliding nozzle plate for hot-cycle operation tundish K.Adachi
11 Classification of clogging behavior of CC immersion nozzle in various stainless steels N.Shiga
12 Clogging behavior of CC immersion nozzle in stainless steels containing Ti H.Todoroki
13 Phosphorous partition between 2CaO•SiO2 particles and CaO-SiO2-FetO slags R.Inoue
14 Behavior of phosphorous transfer between CaO particles and CaO-FetO-P2O5 (-SiO2) slag R.Inoue
15 Characteristics of dephosphorization with slags containing mesoscopic scale 2CaO•SiO2(CaO) particles H.Suito
16 Reaction mechanism between solid CaO and FeOx-CaO-SiO2-P2O5 slag at 1573K S.Fukagai
17 Penetration of molten slag equilibrated with solid CaO by capillary phenomena Y.Ogiso
18 Desulfurization behavior of hot metal by stirring with impeller Y.Nakai
19 Continuous desiliconization by oxygen top blowing to hot metal A.Matsui
20 Slag foaming in multi-refining converter process K.Naito
21 Effect of oxygen blowing condition on hot metal dephosphorization Y.Ogawa
22 Reaction mechanism in slag formation process assisted by thermit reaction T.Asano
23 Formation rate of multi-component calcium ferrite melt M.Kikuchi
24 Influence of coarse iron ore particle on pore formation in sintering M.Hara
25 Influence of operational condition on dust emission from sintering bed M.Nakano
26 Calculation model of rolling length of granule particle
(Simulation model for iron ore granulation by drum type mixer(No.1)) T.Kawaguchi
27 Calculation model of particle size distribution for iron ore granule
(Simulation model for iron ore granulation by drum type mixer(No.2)) T.Kawaguchi
28 Effect of specimen of drum type mixer on granule particle size of iron ore
(Simulation model for iron ore granulation by drum type mixer(No.3)) T.Kawaguchi
29 Numerical modeling of non-isothermal reduction in a hematite pellet with using a mixture of H2-H2O-CO-CO2 Mohammad S. Valipour
30 Dynamic observation method of the reaction at the interface between solid-state-carbon and iron-oxide in TEM N.Ishikawa
31 Carburization and melt-down behavior of reduced iron in iron ore and graphite mixture during rapid heating K.Ohno
32 Pilot plant test for production of iron pebble
(Development of new reduction and smelting process on coal bed-2) H.Hiroha
33 Initial reduction mechanism and dependence of crystal orientation of poly crystal hematite on the reduction by solid carbon Y.Yamaguchi
34 Suitable production condition for pre-reduced agglomerates
(Development of process for pre-reduced agglomerates production-2) S.Machida
35 Reduction mechanism of fine wustite carried by CH4 Y.Nomura
36 Estimation for high temperature property of carbon composite pellet T.Nishimura
37 Reaction behavior of wood flour added coal composite iron ore hot briquettes at high temperatures S.Hayashi
38 Effect of slag on characteristics of swirling liquid jet in transient period D.Iguchi
39 Effects of tracer injection method and bath diameter on mixing time in an inclined cylindrical bath T.Sato
40 Effect of wettability on rising bubble in vertical pipe K.Fukushi
41 Effects of wettability of orifice on behavior of bubble attachment and gas-liquid two-phase flow in pipe D.Maeda
42 Effect of inclined-vortex on entrapment of low density particles into a water bath S.Sato
43 Liquid flow and particle behavior in the presence of swirl motion of bubbling jet in a cylindrical bath Y.Hayashida
44 Effect of sludge on a swirl motion of bubbling jet in highly viscous liquid contained in a cylindrical vessel M.Shitara
45 Characteristics of top-blown jet under vacuum pressure
(Behavior of top-blown jet in vacuum process-1) G.Okuyama
46 Numerical analysis of top-blown jet under vacuum pressure
(Behavior of top-blown jet in vacuum process-2) I.Sumi
47 Model experiment of removal of inclusions in the bath by rising bubbles M.Matsushima
48 Nitrogen absorption rate of molten high Cr steel under pressurized gas condition F.Takahashi
49 Microscopic observation on samples of aluminothermic reduction of magnesium oxide Jian YANG
50 Kinetic analysis of isothermal reduction of MgO with Al Jian YANG
51 Measurement of mass transfer coefficient and heat transfer coefficient between molten iron and solid iron K.Isobe
52 Visualization of collision behavior of particles simulating inclusions in a turbulent flow and its theoretical consideration Y.Murakata
53 Influence of acoustic cavitation phenomena on solidification structure Y.Saiki
54 Effect of design of acoustic reactor on degradation of chemical substances Y.Yoshida
55 Effect of SiC oxidization on corrosion resistance of blast furnace main trough metal line castables M.Iida
56 Application of low thermal conductivity Al2O3-SiC-C bricks to torpedo car H.Shikama
57 Numerical study on the cause of brick drop at the BOF cone K.Tsutsumi
58 Structure analysis for cone lining in BOF S.Uchida
59 Life prolongation of CB nozzle by improved hot castimg at BOF K.Okita
60 Improvement of refractories for molten steel ladle M.Toyota
61 Development of rotary shot method
(Development of rotary shot method-1) H.Imagawa
62 Development of refractories for rotary shot method
(Development of rotary shot method-2) K.Goto
63 Improvement of injection-repair material for RH-degasser bottom brick Y.Nakamura
64 Development of injection refractories of RH part2 T.Terashima
65 Recycling technology of refractories after use in Nippon Steel Corp. S.Hanagiri
66 Confining of molten metal using a high magnetic field Y.Hirono
67 Effect of the imposition of intermittent electromagnetic field on electromagnetic separation of inclusion from liquid metal Y.Kanno
68 Characteristic of agglomeration and separation of inclusion particle in liquid metal agitated by double-axis electromagnetic stirrer S.Hori
69 Acoustic cavitation based sonoprocessing of materials M.Kuwabara
70 Carbothermal reduction of carbon-composite pellets by microwave heating K.Ishizaki
71 Recent activity and future development of in-process technology research group T.Kozuka
72 Effects of alkali metal oxides and CaF2 on thermal conductivities of CaO-SiO2 slags S.Ozawa
73 (ISIJ Research Promotion Grant)
TTT and CCT diagrams and crystallization behavior of various slags T.Nakauchi
74 Effect of slag composition on solidification reaction of iron and steel slag in hydrothermal synthesis M.Hosokawa
75 Adhesions of plants and animals on steel-making slag using as submerged bank material Y.Miyata
76 A prevention technology for solidification of granulated blast furnace slag in seawater H.Mitsufuji
77 Dissolution behavior of chromium from chromium containing crystalline phases into water H.Kanda
78 Analysis of the hydroxide in the slag using an infrared spectrophotometry Y.Fujioka
79 Recovery of metals from Fe2O3-ZnFe2O4-ZnO-PbO with Ar-Cl2-O2 gas by chlorination H.Matsuura
80 Aerosol coagulation in an agitated vessel concerning interaction effect between particles H.Bai
81 Carbothermic reduction of zinc oxide under reduced pressure M.Ogawa
82 Grinding sludge recycling to reduce environmental load
(No.3 technical improvement of separation for further environmental load reduction) K.Nakamura
83 Effect of reactivites of sinter and coke on permeability and coke strength at lower part of blast furnace K.Sunahara
84 Analysis of CRI and CSR tests by a mathematical model considering isothermal fixed-bed Y.Ujisawa
85 Evaluation of high reactivity coke strength after CO2 reaction H.Yokoyama
86 Effect of blast balance on solid flow in blast furnace M.Sawayama
87 Effect of the tuyere placement on mixing molten iron and slag in ironmaking smelter -water model study Su Chau-Jeng
88 Blow-in operation of Kashima No.1 blast furnace(3rd) Y.Saiki
89 Shutdown for exchanging stave and start-up operation of Kakogawa No.1 BF T.Tagawa
90 Control of solidified layer in hearth during shutdown for prolongation of blast furnace life Y.Yamaguchi
91 Prediction of blast furnace productivity with hydrogen-rich injectant T.Sato
92 Effect of casting operation on residual amount of slag and metal under high production operation T.Nouchi
93 Influence of blast humidity on fine ratio in the lower part of furnace T.Orimoto
94 Effect of FeO in dripping slag on drainage behavior of iron and slag in blast furnace hearth K.Nishioka
95 Defining the fundamental properties of metallurgical coke C.E.Loo
96 Effect of coking temperature and holding time at final coking temperature on mechanical property in matrix of metallurgical coke T.Ogata
97 Numerical analysis of coke strength concerning pore shape K.Ueoka
98 Effect of coal particle size on coke size T.Arima
99 Production of high reactivity coke by' post-addition of catalyst to coke' method
(Improvement of blast furnace reaction efficiency by use of high reactivity coke -3) S.Nomura
100 Effect of the production method of the agglomerated coal particles on coke quality H.Fujimoto
101 Effect of raw coal size on formed coke properties K.Kato
102 Thermoplastic performance of the solvent extracted ashless coal N.Okuyama
103 Effects of addition of hypercoal on fusibility of coal blend T.Shishido
104 Effect of the hyper-coal addition to coal on coke strength K.Matsudaira
105 Estimation of coke cake pushing force in commercial oven by using numerical model S.Aizawa
106 Estimation of tolerable limit of localized force on damaged coke oven wall with DEM simulation I.Shimoyama
107 Influence of gas flow pattern on the carbon growth rate from carbonization gas
(Development of carbon deposition control technology in the coke oven-9) T.Nakagawa
108 Development of the combustion chamber observation device K.Tamaoki
109 Effect of smoothing ceramic welding by reheating K.Ohta
110 An approach of replacing the saddle of coke-oven-pusher,based on life diagnosis of equipment
(Maintenance and life extension of the coke oven plant in Sakaide) Y.Kuroiwa
111 Recovery of the butterfly valve control performance at suction main Y.Tsunashima
112 Influence of steel grade and casting conditions on surface cracks of cast steel H.Nakata
113 Evaporation mechanism of lead in molten steel during continuous casting Y.Ohba
114 Effect of mold material and inside surface condition on internal quality of forging ingot S.Suzuki
115 Simulation of gas gap formation during initial solidification M.Miyazaki
116 Effect of hydraulic pressure and water flow rate on cooling ability of water spray T.Murai
117 Development of temperature estimation model of pouring molten steel from ladle T.Nakaoka
118 Development of evaluation method for non-metallic inclusions in steel by high frequency ultrasonic testing K.Sato
119 Low melting-temperature alloy experiment on inclusion entrapment in solidified shell with oscillating magnetic field Y.Miki
120 MnS and Cu2-xS precipitation in strip casting low carbon steels containing phosphorus LIU Zhongzhu
121 Precipitation of Cu and MnS in Fe-Cu-Sn alloys and steels K.Yamamoto
122 Effect of phosphorus contents on phase transformation in a Fe-C-P ternary system K.Igarashi
123 Analysis of grain structure in initial solidification Y.Kuroda
124 As-cast γ microstructural variation with cooling rate after solidification and it's control by direct hot working in micro-alloyed HSLA steels S.Hotta
329 Undercooling and solidification of the middle carbon steel (S45C) by the electromagnetic levitation using AC + DC magnetic fields T.Mizuguchi
125 Effects of various operating factors on formation of inclusions in deoxidation with magnesium vapor T.Yamasaki
126 Reconstruction to tank-type VOD equipment in Yawata works K.Ohnishi
127 Behavior of cavity depth by top-blown jet under vacuum pressure K.Miyamoto
128 Deoxidization of molten iron by hydrogen top-blow K.Kajikawa
129 Refining reaction analysis in Ti bearing high S steel A.Okayama
130 Effect of Mn,Cr,Nb,V on oxygen activity in molten steel and on MnS morphology of low-carbon resulfurized free cutting steel T.Sugimura
131 Control of the ladle slag composition during desulphurization H.Matsumoto
132 Refining effects on non-metallic inclusions of steel with magnesium and barium treatment Li WANG
133 Jet behavior of expansion nozzle with control flow device Y.Hino
134 Development of top and bottom blown converter with wide range of bottom gas flow rate(2) Y.Higuchi
135 Development of on-line tuyere erosion measurement of converter S.Hosohara
136 Application of the oxygen sensor for stainless steel melting Y.Komoda
137 Nitrogen dissolution into molten stainless steel under pressurized atmosphere T.Sugiyama
138 Titanium oxide phase equilibrated with liquid Fe-Ti alloy Woo-Yeol Cha
139 Equilibrium between titanium and oxygen in liquid Fe-Ti alloy coexisted with titanium oxides Woo-Yeol Cha
140 Effect of selenium on supersaturation in aluminum deoxidized molten iron J.Tanabe
141 Thermodynamics of Fe-P-C ternary system formed in pyrometallurgical process for waste treatment T.Matsumura
142 Removal of Ce from CeCl3-KCl molten salt T.Nakajima
143 Solubility of chloride for molten slag Y.Iwasaki
144 Phase equilibria in NaCl-KCl-FeCl2 and NaCl-KCl-CuCl system T.Suga
145 Sulfide capacity of the CaO-Al2O3-CaF2-Nepheline slags S.Kasahara
146 Combining CFD and thermodynamical databases for modelling metallurgical processes
-A novel approach A.Tilliander
147 Gasification of paper + hematite mixture at temperatures between 1673K and 2073K Y.Tanaka
148 Activity coefficient of AgO0.5 in PbO-MOX slag
(MOX:SiO2,Na2O,CaO) T.Kumagai
149 Two liquidus phases separation of Fe-Cu-Sn-B alloy D.Kawauchi
150 (Invited Lecture)
A gasification of graphite by using water gas reaction H.Nishikawa
151 (Invited Lecture)
C2 vibrational and rotational temperatures in high-power and high-pressure Ar-CO2 induction thermal plasmas
152 (Invited Lecture)
Modeling of induction thermal plasmas for material processing T.Watanabe
153 (Invited Lecture)
Measurement of particle temperature and velocity in thermal plasma
using monochrome CCD camera S.Sakiyama
154 (Invited Lecture)
Surface processing by magnetic deflection of arc discharge K.Kusumoto
155 Numerical simulation of heat input characteristics of hollow cathode arc S.Tashiro
156 Relation between voltage and length of twin torch plasma arc due to 98 degree of nozzle angle Y.Hayashi
157 2D temperature and axial radiation power distribution of plasma arc T.Ushijima
158 Virtual experiment of arc melting system with complex interactions H.Takana
Social Engineering on Iron and Steel Industry
159 (Keynote Lecture)
Roles of the government in creating a material circulating society E.Hosoda
160 (Invited Lecture)
Concept for reduction of wastes and minimum usage of resources in public works S.Sone
161 (Invited Lecture)
Obstacles to the environmental business by private enterprises T.Okazaki
162 (Invited Lecture)
Introduction examples on the regional usage of waste heat from industrial plants M.Nakamura
163 Bottleneck of recycling business T.Nakamura
164 Material flow of coal and coal ash through iron making industry T.Nagasaka
165 Utilization and development of iron and steelmaking slag about recent years H.Tobo
166 Present situation and problems of the material recycling in the steel industry K.Yonezawa
167 Material flow analysis of nickel metal
(1)Estimation of amount of domestic supply and waste generation K.Tsunemi
168 Material flow analysis of nickel metal
(2)Estimation of amount of waste treatment K.Tsunemi
169 Collection of stainless-steel with flotation from polishing sludge of special steels M.Katoh
170 Prevention of scale deposits in a water pipe by physical treatment S.Umeki
171 Effect of firing conditions on color tone of glaze for celadon M.Saito
Environmental and Energy Technology
455 Tubular flame burner system
(Low NOx characteristic of a next generation burner system) Y.Hino
456 Catalytic performance of limonite in the decomposition of ammonia in fuel gas N.Tsubouchi
457 Monitoring of gas generated from inorganic materials during pyrolysis M.Nishifuji
458 Combustion rate of woody biomass
(Biomass ironmaking-1) T.Matsuda
459 Simulation of blast furnace operation by woody biomass injection
(Biomass ironmaking-2) K.Wakimoto
460 Effect of iron oxide and carbon catalyses on the methane hydrate formation from snow and ice M.Takahata
461 Removal of phosphate by use of both schwertmannite and high gradient magnetic field A.Eskandarpour
462 Total nitrogen treatment in byproduct plant Park, Yang-ju
463 Influence of water content in slag for carbonation rate of soluble calcium components in steelmaking slag
(Development of stabilization process for steelmaking slag-1) N.Tsutsumi
464 Influence of humidity or temperature for carbonation rate of soluble calcium components in steelmaking slag
(Development of stabilization process for steelmaking slag-2) N.Tsutsumi
465 CO2 absorption and H2 emission under wet grinding of waste cement S.Yokoyama
466 Total materials requirement of energy resources and industrial materials K.Nakajima
467 Material flow analysis of metals based on the waste input-output model K.Nakajima
468 (Keynote Lecture)
Requests to materials scientists and engineers for technological innovation in land-type gas turbine A.Nitta
469 (Invited Lecture)
Improvement of efficiency of small and medium size industrial gas turbines and material technology K.Take
470 (Invited Lecture)
High temperature materials used in advanced sequential combustion gas turbine T.Ito
471 Materials technology evolution for the demand to increase firing gas temperature Y.Yoshioka
472 (Invited Lecture)
Design and development of high temperature materials and plans for their applications H.Harada
473 Development of rhenium-1.5% class high strength Ni-based DS and CC superalloys H.Tamaki
474 Development of Ni-based superalloys for power generation gas turbines
(The improvement of oxidation resistance without any deterioration of creep strength by removing Mo from the alloys) R.Hashizume
475 Microstructure and creep strength of materials for 700�� class USC steam turbines rotor(2) S.Imano
476 Macro segregation tendency of Ni3Al precipitation hardening Ni-Fe base superalloy K.Kajikawa
477 Creep-fatigue property of Nimonic263 K.Kubushiro
478 Orientation dependence of low cycle fatigue behavior in nickel base single crystal superalloy R.Takaku
479 Development of Nb-based superalloys and their diffusion barrier coatings R.Tanaka
480 State-of-art on standardization of high-temperature corrosion testing methods
-Scenario from JSPS methods,JIS and toward ISO- M.Yoshiba
Instrumentation, Control and System Engineering
172 Simultaneous optimization method for storage allocation and transportation in material yard M.Agou
173 A heuristic approach for the bloom group design problem S.Hojo
174 Evaluation of slab transportation capability by logistics simulator T.Iwatani
175 Transportation planning of cranes with immune system derived approach K.Sugiyama
176 Analyzing influential factors of quality change by principal component analysis Y.Nakagawa
177 Independent component analysis of visualized blast furnace process data M.Ito
178 Development of 3-D control technique in raw material yard B.Himeno
179 Development of computer aided software engineering for electrical PLC in large-scale steel manufacture plant T.Ueno
180 Simultaneous visualization measurement of elementary dispersed multiphase flow structure G.Matsui
181 Magnetohydrodynamic calculation method for electromagnetic sensor S.Fujino
182 Measurement of hydraulic oil leak of skirt cylinder Hyungkuk Park
183 Development of high sensitivity EMAT technique Y.Iizuka
184 Development of non-contact testing using electromagnetic acoustic transducer for steel sheets T.Nakata
185 Principle of a new internal defect detector for hot rolled steel sheets using magnetic leakage flux method H.Kato
186 Surface flaw testing of steel material by new eddy current probe Y.Tanaka
187 Measurement technique of material properties of plate steel using laser-based ultrasonics
(Part1:measurement of austenite grain size) Choong Soo Lim
188 Measurement technique of material properties of plate steel using laser-based ultrasonics
(Part2:measurement of recrystallization ratio and grain aspect ratio) Y.Nagata
189 Development of on-line cutting profile of internal bead on ERW steel pipes T.Kodama
Processing for Quality Products
190 Measurement technology of surface roughness and its application for on-line use A.Torao
191 Printing behavior of roll surface texture to zinc coated steel in temper rolling Y.Kimura
192 Influence of the difference of roll roughness processing on transcription in temper rolling Y.Aramaki
193 Change in the surface qualities under dry condition in temper rolling
(Surface qualities of workpiece and behavior of lubricant in temper rolling-1) K.Aoki
194 Effect of the lubricant on roll surface transcription in skinpass rolling process N.Nagase
195 Theory for rolling with very light reduction H.Matsumoto
196 FE simulation of non-uniform plastic deformation in temper rolling F.Yoshida
197 Stress and strain analysis in temper rolling for mild steel sheet by elastic-plastic finite element method I.Yarita
198 Analysis of luders bands in temper rolling by the continuum theory of dislocations K.Komori
199 Surface roughness transcription FEM analysis using zooming method N.Yukawa
200 Simulation of deformation and temperature in bar rolling
(Effect of finite-element mesh in cross section) K.Komori
201 Basic research on surface defect deformation behavior in steel bar rolling K.Takezawa
202 Analysis of surface defects on bar and wire rolling H.Kushida
203 Development of interface between two step meshing method and Samukawa's multiple skyline method
(Development of the modern interface for FEM analyses of plastic workings-6) T.Yoshida
204 Effect of additional shear strain layer on strength and ductility of fine drawn wire S.Kajino
205 Effect of O2,N contents on drawability of titanium wire K.Takahashi
206 Characteristics of load reduction and influence on microstructure by swing motion forging
(Grain refinement by large reduction forging technology-5) M.Miyake
207 Effect of lubrication on hot rolling of ultra-fine-grained strip
(Development of super short interval multi-pass rolling technology for ultra-fine-grained steel-8) T.Sasaki
208 Effect of thermomechanical treatment on grain refinement
(Grain refining investigation by complex rolling/bending multiple accumulation process-4) Y.Matsubara
209 Analysis of thermal history of strip in multi-bending process after hot rolling N.Nakata
210 Micro-scale modeling for the prediction of microstructure evolution after severe plastic deformation
(Part6:experiments to obtain material data) A.Yanagida
211 The evaluation of lubricity of lubricant by simulation testing machine for hot rolling Xue Wei-dong
212 Hot rolling performance estimation of super cermet rolls Y.Kamitani
213 Characteristics of liquid colloidal lubricants with solid powder lubricant and inorganic compound-4 J.Ikeda
214 Effects of oxide scale of plug on piercing properties-II- Y.Hidaka
215 Development of 780MPa class small diameter electric-resistance-welded (ERW) tube manufacturing technology T.Sawaki
216 Effect of C,Si,Mn contents and welding atmosphere on the formability in electric resistance welded tube T.Okabe
217 T-shape hydroforming of a mash-seam welded tube H.Nakamura
218 Development of forming setup system for 4inch ERW mill H.Hori
219 Characteristics of circular tube bending on MOS method by FEM M.Murata
220 Examination of body structure and metal optimization for weight reduction in body white
(Examination of body structure and metal optimization-1) M.Ono
221 Effect of steel tube cross-sectional shape on initial peak reaction force in bend crush
(Examination of body structure and metal optimization-2) S.Sakamoto
222 Development of the new steel sheet pile
(HAT-profile sheet pile) S.Taenaka
223 Permeability of the sheet pile joints with a pocket sealed with sealant/expanding rubber as a hydraulic barrier Y.Oka
224 Development of impermeable method characterized by welding the joints of Box-J piles H.Shikano
225 Production technology development of stainless steel H shapes by 2-roll mill K.Shibata
226 Establishment of thermomechanically controlled rolling process of SUS630 K.Hattori
227 (ISIJ Research Promotion Grant)
Numerical study of collision of a liquid droplet with a hot substrate H.Fujimoto
228 The experiment study of the rapid cooling by rolls Y.Serizawa
229 Effect of water pressure on flat spray cooling capacity Y.Haraguchi
230 Effect of forming conditions on shape-fixability in hat-shaped forming H.Ohgusu
231 Warm and hot hat bending of high strength steel sheets using resistance heating K.Mori
232 The experimental observation for plastic deformation behavior of high tensile strength steel sheet under non-proportional loading T.Uemori
233 Analysis of sheet rolling with surface dent H.Matsuzawa
234 Influence of carbon and chromium content on machinability of cold work die steel T.Shimizu
235 (ISIJ Research Promotion Grant)
Development of FSW apparatus for steels T.Nishihara
236 Microstructure and deformation properties of austenitic stainless steel with FA solidification mode in semi-solid state Jingyuan Li
237 Microstructure and deformation properties of SUS430 in semi-solid state Jingyuan Li
238 Effect of WC binder on the corrosion resistance of self-fuzing thermal spray coating with WC cermet S.Midorikawa
239 Simulation of grain boundary diffusion with stress gradient due to surface tension K.Shinagawa
240 Quality improvement technique for micro metal injection molding products H.Miura
241 (Invited Lecture)
Optimization of steel castings design by CAE K.Yamada
242 Influence of mass effect on mechanical properties of large carbon steel casting M.Okino
243 Microstructures and characteristics of high Cr-Ni heat resistant cast steel K.Hashimoto
244 Development of the exhaust component material for high performance gasoline engines K.Itoh
245 (Invited Lecture)
Dry and wet wear resistance and toughness of high speed steel type alloy containing high carbon and high chromium cast iron A.Sawamoto
Microstructure and Properties of Materials
246 Effects of carbon and phosphorus addition on the fatigue properties of ultrafine ferrite-cementite steels Y.Furuya
247 Effect of hydrogen on the gigacycle fatigue properties of low alloy steels H.Hirukawa
248 1010-cycles fatigue properties of S40C steel for machine structural use T.Abe
249 Description of true stress-strain curves of ferrite singles microstructure steels with a wide range of grain size M.Shimada
250 (ISIJ Research Promotion Grant)
Effects of lath-structure on mechanical properties in a bainitic steel H.Okubo
251 Effects of interstitial content and partial recrystallization on cyclic deformation structure at low temperature
(High-cycle fatigue behavior of extra-low carbon steel-3) O.Umezawa
252 Estimation of CTOD for a toe crack in non-load-carrying tee fillet welded joints T.Inoue
253 Equation to estimate critical CTOD from charpy impact energy for structural steel with strength range from mild steel to HT780 T.Handa
254 Experimental clarification on steel properties controlling ductile crack extension M.Ohata
255 Analysis of criterion for ductile crack initiation of high strength steels under cyclic loading H.Sueyoshi
256 Evaluation of fracture toughness after ductile crack extension T.Tagawa
257 (ISIJ Research Promotion Grant)
Evaluation of characteristic microstructures on the impact fracture surfaces of SS400 steel M.Tanaka
258 Study on the simulation method for propagating shear fracture in offshore pipeline T.Inoue
259 Fracture toughness test by various size round bar specimen with a circular notch T.Murakami
260 Combined effect of temper and hydrogen embrittlement on impact properties of Cr-Mo steels
(Temper and hydrogen embrittlement in Cr-Mo steels for pressure vessels-1) S.Aihara
261 Relation between microstructural evolution and fatigue life during rolling contact H.Hidaka
262 Precipitation behavior of V added Ni-Fe based super alloy N.Hirota
263 (ISIJ Research Promotion Grant)
Alloy design and microstructural control of Ni-based multi-intermetallics with ultra fine dual multi-phase microstructures T.Takasugi
264 Change in crystallographic orientation with creep deformation in γ -single phase Ni-20Cr alloy polycrystalline Y.Nakajima
265 Creep deformation at low-stress in Ni-20mass%Cr alloy single crystal with [111] orientation S.Maeda
266 Creep deformation under lower stress condition in Ni-20mass%Cr single crystal with [011] orientation M.Mitsutake
267 Change in creep deformation with different orientations in γ single phase Ni-20mass%Cr single crystal located within standard stereographic triangle K.Yuge
268 Change in morphology of γ ' phase and dislocation substructures of single crystal Ni-based superalloy,CMSX-4,pre-crept at 1273K-250MPa with simple aging K.Kurita
269 Change in orientation with creep deformation in PST whose orientation between lamellar plate and stress axis is 40° E.Sakurada
270 Adaptability of hot-rolled sheet steel with strain age hardenability in tensile strength for application to automotive parts T.Mochida
271 Influence of micro structure on increase in tensile strength induced by strain age hardening S.Kaneko
272 Crack propagation behavior in hole expanding test of hot-rolled steel sheet strengthened by nanometer-sized precipitates A.Kobayashi
273 Effect of ferrite grain refinement by dynamic recrystallization on stretch-flangeability in sheet steel E.Yasuhara
274 Effect of die diameter on hole expanding ratio of high-strength hot-rolled steel sheet H.Tanahashi
275 Microstructures of C-Si-Mn-Cr-Mo steels cooled at various rates after high-temperature austenitization D.Kondo
276 Effects of oxide scale on the lubricity during hot rolling(II) Y.Hidaka
277 High-temperature oxidation and subscale formation of Si containing steels K.Kusabiraki
278 Effect of cooling condition on mechanical properties of TRIP-aided steel with bainitic Ferrite
(Development of high strength steel with good delayed fracture performance-1) H.Akamizu
279 Development of 1470MPa grade cold rolled steel
(Development of high strength steel with good delayed fracture performance-2) S.Kozuma
280 Evaluation of susceptibility to hydrogen embrittlement of 1470MPa grade cold rolled steel F.Yuse
281 (ISIJ Research Promotion Grant)
Effects of Nb addition on stretch-flangeability of ultra high strength low alloy TRIP-aided steels with bainitic ferrite matrix T.Muramatsu
282 Effects of alloying element on delayed fracture strength of ultra high-strength low alloy TRIP-aided steels T.Hojo
283 Press formability of 980MPa TRIP aided bainitic ferrite cold rolled steel sheet M.Nakaya
284 Thermo-mechanical forging in γ region of high-strength low-alloy TRIP-aided steels
(Microstructure and retained austenite characteristics) M.Ito
285 Acoustic emission signals generated during deformation of TRIP aided steels with different matrix microstructures
286 Relationship between mechanical properties and transformation of blocky and lath-shaped retained austenite during straining H.Matsuda
287 Effect of transformation behavior of retained austenite on yield ratio J.Haji
288 Modelling of phase transformations and mechanical properties in high strength steels with continuous annealing K.Hayashi
289 A model for phase transformations and mechanical properties in high strength steels with continuous annealing process M.Azuma
290 Effect of curing methods on sliding properties of thin organic composite coated steel sheet T.Matsuda
291 Effect of silica on corrosion resistance of chromate-free type thin organic composite coated steel sheet K.Yamamoto
292 Effect of composition of steel on durability of paint Y.Harada
293 Relationship between corrosion of ED-coated steel and characteristics of phosphate K.Yuasa
294 Effect of melamine contents on the rheological properties and resin structure of paint films K.Ueda
295 Effect of film structure and property on performance of polyester/melamine resin films M.Fuda
296 Effect of Cr content for adhesion durability of organic coated steel M.Murase
297 Reduction of bubble by controlling laminating atmosphere H.Date
298 Mechanism of formation and types of defects on hot-dipped galvanized steel sheet A.Sato
299 Effect of substrate properties on the microstructure of galvannealed steel sheet Kim Dong-Hyun
300 Clarifying the controlling factor of surface defects of galvannealed high tensile sheet steel Y.Suzuki
301 Evaluation for dynamic wetting of molten zinc to steel substrate containing Si and Mn S.Shimada
302 Galvannealing behavior in initial stage during hot dip galvanizing of P added steel E.Hamada
303 Galvannealing behavior in initial stage during hot dip galvanizing of Si added steel E.Hamada
304 (ISIJ Research Promotion Grant)
Analysis of multiple cracking of coating layer of galvannealed steel S.Ochiai
305 Behavior of Ni displacement deposition onto galvannealed steel sheets T.Imokawa
306 Effect of pre-heating on weldability of galvanized steel M.Nakazawa
307 Surface texture analysis of hot-dip galvanized steel by 3D-SEM H.Noro
308 Numerical analysis of cathodic protection distance for zinc coated steel sheet N.Okada
309 Effect of corrosion products formed in the atmosphere on potential of galvanized steel in sea water Y.Makimizu
310 Hydrogen induced quasi-cleavage fracture of high strength martensitic steel T.Kawakita
311 (ISIJ Research Promotion Grant)
Effect of applied stress on hydrogen trapping states and mechanical properties of cold-drawn pearlite steel with various activation energies K.Nakano
312 Effect of alloy carbide on hydrogen absorption property in CCT
(Precipitation hardening and hydrogen trapping behavior in high strength steels-3) T.Chida
313 Ab initio calculations of the energy of formation for 3d transition metal borides T.Tokunaga
314 Computational simulation of plastic deformation behavior of low-carbon TRIP steel K.Saito
315 Monte carlo simulation on the morphology of the second phases at the inter-critical annealing in steel K.Okuda
316 Monte-carlo simulation of grain growth in heat-affected-zone in steel welds T.Araki
317 Influence of specimen's shape on vacuum carburizing T.Morita
318 Modelling precipitation of (V,Mo)4C3 carbide in martensitic steels S.Yamasaki
319 Precipitation behavior of Cu particles in an Fe-1.5mass%Cu alloy T.Yamashita
320 Simulation of Cu precipitation in tempered martensitic steels J.B.Yang
321 Precipitation analysis of Cr- and Cu-added nitriding steel surface by 3D-AP
(Nitriding processes of Cu-added steels-3) J.Takahashi
322 (ISIJ Research Promotion Grant)
STEM-EDXS analysis of copper at prior austenite grain boundaries S.Hata
323 Substitution of W and Cr for Mo in (Ti,Mo)C complexcarbide M.Suwa
324 Grain growth and microstructural evolution of liquid-particle dispersion structure in iron base alloys T.Hagisawa
325 Prior austenite grain size and segregation behaviour in 2.25Cr-1Mo steel M.A. Islam
326 Influence of cold reduction ratio and heating rate on recrystallization behavior for ultra low carbon steel T.Kizu
327 Difference in softening behavior between deformed martensitic steel and deformed ferritic steel M.Natori
328 Effects of aging and alloying elements on mechanical properties of chromium steels M.Mogi
330 (Program for Stategic Research Projects)
Temperature dependence of Hall-Petch coefficient in iron S.Takaki
331 (Program for Stategic Research Projects)
Change in hall-petch coefficient of austenitic steel with solid-solutioning of nitrogen T.Tsuchiyama
332 (Program for Stategic Research Projects)
Relation between yield strength and nominal grain size in duplex-grained steel R.Matoba
333 (Program for Stategic Research Projects)
Importance of size-distribution of dispersed particles in evaluation of yield strength of particle-dispersion-strengthened ferritic steel T.Kitaura
334 (Program for Stategic Research Projects)
Precipitation strengthening by Cu particles in Fe-Cu alloys K.Nakashima
335 (Program for Stategic Research Projects)
Change in tensile deformation behavior with aging treatment in Cu-bearing steel T.Hosoda
336 (Program for Stategic Research Projects)
Effect of wire diameter and grain size on tensile properties in austenitic stainless steel wire T.Fukumaru
337 (Program for Stategic Research Projects)
(Wire diameter/grain size)ratio dependence of tensile properties in As-drawn austenitic stainless steel wire T.Fukumaru
338 (Program for Stategic Research Projects)
Tensile property of ferritic stainless steel thin wire fabricated from mechanically alloyed powder T.Onomoto
339 (Program for Stategic Research Projects)
Yielding behavior of ultralow carbon martensitic steel and its change by cold-working Y.Fujimura
340 (Program for Stategic Research Projects)
Effect of carbon on work hardening behavior of martensitic steel K.Nakashima
341 (Program for Stategic Research Projects)
Deformation behavior of ultra fine grained iron S.Takaki
342 Development of Fe-Ni base austenitic alloys for piping in 700�� USC power plants H.Okada
343 Relationship between phase transformation and grain boundary fracture in seamless pipe of SUS321 steel during creep deformation M.Mitsuhara
344 Precipitation behavior during long-term creep of SUS347 steel H.Tanaka
345 The development of the low alloy steel with superior short time creep strength at high temperature S.Muneki
346 Characterization of creep deformation behavior of 0.5Cr-0.5Mo steel by stress change test S.Nakashima
347 Variation of interparticle spacing in creep deformation of low alloy steels for thermal power boiler tubes Y.Nakazato
348 Effect of oxide scaling on creep rupture life of 2.25Cr-1.6W steel M.Yoshizawa
349 Remaining life evaluation of long-term used 2.25Cr-1Mo steel boiler elbow T.Ito
350 Evaluation of aging deterioration of welded joints in long-term service-exposed boiler by small specimen test technique T.Sugimoto
351 Microstructual development during creep in weldment of mod.9Cr-1Mo steel K.Kubushiro
352 Relationship between the hydrogen dissolution and the oxidation resistance in ferritic steels exposed to high-temperature steam K.Nagai
353 Effect of oxygen content in Ar gas on formation of Cr-rich protective oxide scale by pre-oxidation in argon H.Kutsumi
354 The strain rate sensitivities of flow stresses of a mild steel and high strength steels S.Takagi
355 Effects of bake hardening property on dynamic yield strength of ultra high strength sheet steels T.Masuda
356 Yield stress anisotropy by straining and baking of bake-hardenable sheet steel S.Yonemura
357 Evolution of microstructure of IF steel deformed by tension Y.Ikematsu
358 Evaluation of hydrogen embrittlement susceptibility for sheet steel K.Hayashi
359 Effect of chemical compositions and manufacturing conditions on mechanical properties
(Development of high strength galvannealed steel sheets with excellent formability:part1) H.Tanaka
360 Effect of microstructure prior to annealing on spheroidization behavior of high-carbon steel sheet H.Kimura
361 Effect of microstructure on elongation of high carbon steel sheet
(Effect of void initiation on elongation) N.Kariya
362 Determination of smut on pre-treated surface of steel sheet for porcelain enamel and estimated mechanism of adhesion of enamel layer to steel Y.Ishiguro
363 Magnetic properties of siliconized grain oriented electrical steel T.Hiratani
364 Influence of heat treatment prior to cold rolling on recrystallization texture in 3% Si steel Y.Shingaki
365 Influence of grain misorientation angle on the selective growth of Goss grain in grain-oriented electrical steel T.Oomura
366 Effect of crystal orientation on the high frequency iron loss of 3%Si-Fe single crystal T.Okubo
367 Effects of laser-irradiation on iron loss reduction for Fe-3%Si grain-oriented silicon steel M.Imafuku
368 Magnetic properties and textures in abnormal grain growth of non-oriented electrical steel sheets Y.Arita
369 Influence of shearing process on domain structure of non-oriented electrical steel K.Senda
370 Effect of annealing tension on anhysteretic permeability of steel sheets for magnetic shield N.Mineji
371 Effect of texture on magnetic properties of 36% Ni alloy sheet K.Fujita
372 Effect of boron contents on grain growth in ultra-soft austenitic stainless steel M.Hatano
373 Effect of C and N on mechanical property in austenitic stainless steel containing Cu E.Ishimaru
374 Effect of deformation condition and chemical composition on strain induced martensite in austenitic stainless steel T.Mizoguchi
375 Retardation of 20%Cr steel oxidation with laves phase precipitation S.Ide
376 Effect of Si on oxidation resistance of ferritic stainless steels N.Hiraide
377 Effect of Si on oxidation behavior of Al containing ferritic stainless steel in an exhaust gas atmosphere Y.Inoue
378 Effects of Nb content and annealing temperatures on microstructure and strength of high purity 19Cr stainless steels M.Abe
379 Properties of Fe-Cr-Mo-Mn-N alloy powder and consolidated materials fabricated through mechanical alloying method under nitrogen atmosphere Y.Nakamura
380 Effect of specimen diameter on tensile properties of austenitic stainless steels in liquid hydrogen and gaseous helium at 20K S.Ohmiya
381 Evaluation of residual plastic strain and low-cycle-fatigue damage by electron backscatter diffraction patterns R.Yoda
382 Microstructural change with aging treatment in SUS316(LC) austenitic stainless steel K.Mizotani
383 Effects of alloy elements on casting structures in Cr-Mn-Ni austenitic stainless bases T.Oshima
384 Tensile property of stainless steels exposed to high pressure gaseous hydrogen for a long time H.Nakagawa
385 (ISIJ Research Promotion Grant)
Hydrogen absorption and degradation susceptibility of cold-drawn high-strength stainless steel wires H.Yaginuma
386 (ISIJ Research Promotion Grant)
Microstructure and photocatalytic property of titanium oxide dispersion SUS304 stainless steel Y.Senda
387 Influence of UV irradiation on titanium and titanium alloy of macro wettability K.Mukai
388 Analysis of water wettability associated with corrosion of Ti and Ti alloy F.Suzumura
389 Development of high performance 570MPa class steel by TMCP for bridge H.Onishi
390 Effect of alloying elements on the refinement dispersion of cementite in rapidly heated tempered steels A.Nagao
391 Development of API X-80 grade electric resistance welding line pipe with excellent low temperature toughness H.Nakata
392 Heat treatment online process for a new material designing technology-1
(Transformation and precipitation behavior during accelerated cooling and on-line heating) N.Ishikawa
393 Heat treatment online process for a new material designing technology-2
(Developement of highstrength sour resistant linepipe produced by heat treatment on-line process) N.Ishikawa
394 Heat treatment online process for a new material designing technology-3
(Development of high strength with superior deformability linepipe) M.Okatsu
395 Heat treatment online process for a new material designing technology-4
(Development of high strength structural UOE pipe applied by heat treatment on-line process) R.Muraoka
396 (ISIJ Research Promotion Grant)
Influence of MnS and sub-boundary on enhancement of nucleation of intragranular bainite N.Kanno
397 Investigation of ferrite transformation behaviors from steel-oxide interface H.Kato
398 Influence of oxide particle compositions on intra-granular ferrite formation in titanium oxide steels A.Kojima
399 Effect of cooling stop temperature on transformation of lower bainite in low carbon high strength steel J.Shimamura
400 Effect of niobium addition on transformed structure of low carbon steel T.Yamaguchi
401 γ grain uniformity behavior after abnormal α to γ transformation
-Mechanism of abnormal α to γ transformation (5)- T.Hara
402 Bainite transformation during two-stage isothermal treatment K.Hase
403 (ISIJ Research Promotion Grant)
Diffusion of carbon and titanium in γ -iron in a magnetic field and a magnetic field gradient S.Tsurekawa
404 Construction of thermodynamic database for multi-component Fe alloys applying first-principle calculations N.Hanaya
405 Phase equilibria in Fe-V-S ternary system T.Sasaki
406 Phase equilibria in Fe-Mn-Al-C system N.Kamiya
407 Dissolution of lamellar and spheroidal cementites in carbon steels by ball drop deformation and laser heating Y.Todaka
408 Estimation of long term rupture strength of high Cr steel by exponential equation M.Tamura
409 Effect of tempering condition on transient creep of modified 9Cr ferritic steel N.Sekine
410 Creep life and hardness changes of Mod.9Cr-1Mo steel H.Chitaka
411 Effect of Al and Si on creep properties of carbon-free Fe-12Ni-9Co-10W martensitic alloys S.Muneki
412 Effect of nitrogen on creep deformation behavior of high-B 9Cr-3W-3Co steels H.Semba
413 Effects of boron addition on formation of carbides during aging in 0.1C-9Cr-3W-3Co steels M.Yamaguchi
414 Effect of N on creep properties of B added 10%Cr ferritic heat resistant steels M.Mikami
415 Improvement of long-term creep rupture strength of 9%Cr-W-Co ferritic steel for USC boiler components T.Sato
416 Stress relaxation behavior of 9Cr-0.5Mo-1.8W-V-Nb steel T.Ohba
417 Influence of laves phase contents on toughness degradation with aging in high Cr steels T.Takahashi
418 Behavior of formation of boron nitrides in high Cr ferritic heat resistant steel P122 K.Sakuraya
419 Effect of thermomechanical heat treatments combined with magnetic field on the microstructure of a high Cr ferritic heat resistant steel H.Okubo
420 Precipitation behavior of Z phase during long-term creep exposure in 9-12%Cr steels K.Sawada
421 Calculation of phase equilibrium between γ phase and MX carbonitride in mod. 9Cr-1Mo steel Y.Toda
422 Influence of δ -ferrite on degradation behavior of high Cr ferritic creep resistant steels M.Yoshino
423 Effect of MnS on machinability in low C steel M.Hashimura
424 Effect of MnS on machined surface characteristics in low C steel M.Hashimura
425 Evaluation of surface profile created by plunge cutting tool with grooves in S10C K.Miyanishi
426 The effect of titanium and niobium on machinabitity of case-hardening steel M.Hayaishi
427 Improvement of contact fatigue resistance of SCr420 steel by vacuum carburizing K.Ono
428 Effect of carbonitriding and chemical compositions on tooth surface strength Y.Shindo
429 Effect of carbon content and hardness profile on the low cycle impact fatigue properties in carburized steels T.Miyazaki
430 Effect of Mn on the austenite grain growth property-2- T.Fujimatsu
431 Effect of Ti on impact properties in an air hardened microalloy forging steel
(Development of an air hardened microalloy forging steel for fracture splitting connecting rods) T.Hasegawa
432 Mechanical properties of high heat resistant oil tempered wire Y.Fujino
433 Effect of microstructure on abrasive wear resistance in carbon steels K.Takeda
434 Effect of toughness and cleanliness on heat check resistance of hot working die steel S.Tanaka
435 Effect of alloy elements on tensile properties of bar with welded joint T.Iwamoto ...... 1636
436 Structural analysis of passive films on stainless steels after 10 years atmospheric exposure S.Okada
437 Corrosion behavior of Cr-Mn-Ni austenitic stainless steels in acid environment M.Arima
438 Effect of electrode potential on solution chemistry inside a crevice T.Shinohara
439 Effects of chemical components on resistance to intergranular stress corrosion cracking in heat affected zone of martensitic stainless steel Y.Miyata
440 Effect of microstructures of metals on adhesion behavior of microbes
(Adhesion behavior of microbes to surface of stainless steel,titanium and copper) Y.Miyano
Process Evaluation and Material Characterization
441 Surface analysis using STM in the process of reducing iron oxides(2) T.Yamashita
442 Surface analysis using STM in the process of reducing iron oxides(3) Y.Masaki
443 Nano-precipitation in steels observed using low-voltage scanning electron microscopy K.Yamada
444 Photoemission studies of the oxide film on the hot-dipped Zn-Al coated steel sheets K.Nishihara
445 Elemental analysis of electroplated Fe-Zn alloys based on Vegard's law H.Noro
446 Estimation of inclusion size in stainless steel coil based on statistics of extreme values Y.Kanbe
447 Solid-state 25Mg NMR of various inorganic compounds K.Saito
448 Application of laser induced breakdown spectroscopy to on-site analysis of steels Y.Usui
449 FeO analysis in sinter ore by magnetic balance with permanent magnet M.Aimoto
450 Simple quantification of surface carbon on steel sheet A.Chino
451 Analytical performance in optical emission specrometry using Ar spark discharge plasma under reduced pressures K.Wagatsuma
452 Development of rapid analytical method of carbon in steels by glow discharge optical emission spectrometry H.Yasuhara
453 Electrothermal vaporization of refractory elements as 8-quinolinolate complexes in inductively coupled plasma atomic emission spectrometry T.Matsushita
454 Elemental analysis of iron and steel by solid-phase extraction using a extraction disk S.Hasegawa
ISIJ and JIM Joint Session
J1 Microstructural control in surface layers of high purity titanium sheets and photocatalytic activity of the oxide films Y.Takayama
J2 Surface hardening and post-heat treatment effect in C.P.titanium and titanium alloys in use of CO gas Yuanzhe Kim
J3 Formation of TiO2 nanotube layers by anodization H.Tsuchiya
J4 Coating of Ti alloys in molten salt T.Takenaka
J5 Reduction of TiCl4 by the electrolysis of molten calcium chloride T.Naito
J6 Alloy design of high formability titanium alloys for elevated temperature applications
(Development of high formability titanium alloys for elevated temperature applications-1) H.Fujii
J7 High temperature performances of new high-formability titanium alloys for elevated temperature applications
(Development of high-formability titanium alloys for elevated temperature applications-2) H.Fujii
J8 Cold formability of new high-formability titanium alloys for elevated temperature applications
(Development of high-formability titanium alloys for elevated temperature applications-3) K.Takahashi
J9 (ISIJ Research Promotion Grant)
Powder nanotechnology for TiAl H.Kimura
J10 The effect of solution treatment conditions on the creep properties of TiB particulate reinforced Ti-22Al-27Nb composite S.Emura
J11 Separation of hydrogen states by thermal desorption spectroscopy and degradation behavior of pure-titanium H.Yamada
J12 Effect of elevated temperature exposure on mechanical properties of Ti-4.5Al-0.5Fe-0.2C-(Cr.Mo.V) T.Tanaka
J13 The characteristics of the Ti-20V-4Al-1Sn alloy produced by α + β process S.Matsumoto
J14 Development of beta-titanium alloy bolts N.Matsukura
J15 Study of phase transformations in a β-Ti-Mo alloy prepared by a two step aging method using electron microscopy E.Sukedai
J16 Change of elastic behavior in binary β-type Ti alloys with deformation Y.Takemoto
J17 Development of TiV(Sn) alloy with low Young's modulus and high strength H.Matsumoto
J18 Effect of C addition and aging on microstructure and mechanical property of TiNbAl alloy Y.Horiuchi
J19 Characterization of deformation behaviors of β type titanium alloys using X-ray diffraction analysis under stress loading conditions N.Sakaguchi
J20 Dimensional accuracy and mechanical properties of titanium alloys for biomaterial applications cast into calcia mold H.Chikusa
J21 Effect of oxygen content on phase constitution and heat treatment behavior of Ti-Ta-Zr alloys M.Mori
J22 Effect of Sn content on phase constitution and heat treatment behavior of Ti-4.3mass%Fe-7.1mass%Cr-Sn alloys H.Miyawaki
J23 The principles of nanostructuring of steel using SPD processing Ruslan Z. Valiev
J24 On the mechanisms governing the special properties of SPD nanometals Michael.J.Zehetbouer
J25 Microstructural evalution in 7475 Al alloy during severe warm forging A.Goloborodko
J26 Tensile mechanical properties of ultra fine-grained magnesium alloys at high strain rate T.Mukai
J27 Seven approaches to improve the tensile ductility of ultra-fine grained and nanostructured metals E.Ma
J28 Effect of equal channelangular pressing on the mechanical properties of metals Yuri Estrin
J29 Nanoindentation-induced deformation behavior in the vicinity of single grain boundary T.Ohmura
J30 Size effects in plasticity:experiments and simulations Helena Van Swygenhoven
J31 Mechanical properties of nanocrystalline Al and Cu by molecular dynamics simulations T.Shimokawa
J32 New routes to synthesize massive nanostructured materials Gerhard Wilde
J33 Role of strain gradient on the formation of nanocrystalline structure produced by severe plastic deformation M.Umemoto
J34 Nanocrystalline structure formed on the worn surface in carbon steel J.G.Li
J35 Microstructural evolution of pearlite steel severely deformed by surface mechanical attrition treatment H.W.Zhang...... 1739
J36 Grain refinement during severe plastic deformation of steels S.V.Dobatkin
J37 Formation mechanism of five-fold deformation twins in nanocrystalline fcc metals Yuntian T.Zhu
J38 Grain refinement using torsion straining technique Z.Horita
J39 Bulk nanocrystalline Fe-C steel processed by mechanical milling ans spark plasma sintering K.Hono
J40 Miscrostructure evolution of mechanically milled martenstie steel powder S.Ohsaki
J41 Grain boundary diffusion as the controlling mechanism of ferrite grain size during large strain high Z deformation in low carbon steel S.V.S Narayana Murty
J42 Influence of initial grain size on the formation of ultrafine ferrite structure during large strain high-Z deformation in ultra-low carbon steel S.V.S Narayana Murty
J43 Friction stir welding of plain low-carbon steels with ultrafine grained microstructure fabricated by martensite method R.Ueji
J44 Strength - reduction in area balance of ultrafine-grained steel and its formability S.Torizuka
J45 Cutting performance of ultrafine grain steel T.Komatsu
J46 Surface hardening of ultrafine-grained steel by gas soft-nitriding N.Takagi
J47 Mechanical property and microstucture of copper deformed by the ARB process B.L.Li
J48 Microstructure and mechanical properties of Al-X solid solutions severely deformed by ARB T.Masui
J49 Evolution of ultrafine grained structure and its mechanical properties of commercial purity Ti severely deformed by ARB S.Inoue
J50 Outline of "application of ultra-fine grained steel sheet to automobile" project K.Tsuzaki
J51 Determination of plastic working limit by circumferentially notched tension test K.Enami
J52 Application of evaluation method for freebulge forming in ultra-fine grained steel
-Proposal for determination of forming limit curve- T.Kimura
J53 Effects of temperature and strain rate on stress-strain relation for ultrafine-grained steels N.Tsuchida
J54 Numerical simulation of high speed collapse of electric resistance welded UFG steel pipe Y.Okitsu
J55 Amorphization/nanocrystallization and martensitic transformation in TiNi shape memory alloys after severe plastic deformation K.Tsuchiya
J56 Deformation of nanocracrystalline Al alloys investigated by nanoindentation Jin Man Jang
J57 A study on compressive deformation behaviors in nanocystallin alloys Won Sik Lee
J58 Fine-grained structures associated with deformation twin and its influence on tensile behaviors in cold-rolled ferrous alloys T.Morikawa
J59 Microstructure and mechanical properties of Cu-30%Zn alloy heavily deformed by ARB and annealed N.Shigeiri
J60 High temperature deformtaion behavior and microstructure change in nano-grain composites N.Miyano