Program of the 142nd ISIJ Meeting (September 22-24, 2001)
General Presentation Only (Program;PDF)
Current Advance in Materials and Process, Vol.14 ,No.4
1 Quantitative analysis of circulating solid velocity field in raceway M.Sawayama…841
2 The measurement of solid temperature in a race way using two colors thermometers by CCD camera S.Matsuzaki…842
3 Control of CO2 peak point by dual lance air curtain method M.Ichida…843
4 Analysis of phenomena at lower part in blust furnace by sampling at tuyer level-2 Y.Hayasaka…844
5 Development of waste plastics recycling process using coke ovens K.Kato…845
6 Fundamental experiments on the H2 gas injection into the lower part of a blast furnace shaft T.Usui…846
7 Consideration and practice of science, technology and strategy for minimizing CO2 emission in Chinese
steel industry D.Cang…847
8 Evaluation of emerging iron and steelmaking-an LCA approach L.Wibberley…848
9 Dezincing behavior from iron and steelmaking dusts by microwave heating K.Nishioka…849
10 Recycling of shredder residue in ironmaking process H.Hiroha…850
11 Numerical simulation of the moving bed furnace for iron scrap melting R.Takahashi…851
12 Scrap and dust treatment technology for multi-function reducing-melting furnace M.Naito…852
13 Influence of sulfur activity on the reforming reaction during production of iron carbide
with CO-CH4-H2-H2S mixtures in fluidized bed T.Kouda…853
14 Energy and pollutants reducing technologies in new ironmaking processes at POSCO I.O.Lee…854
15 Estimation of the clearance between coke-cake and oven wall S.Aizawa…855
16 Investigation into the coke oven walls in Kakogawa applying the mobile chamber width measuring system N.Takayama…856
17 Hot repair in the chamber end part of Mizushima No.1 coke oven M.Homma…857
18 Combustion chamber of observation and repair equipment in Yawata No.4 coke oven S.Ikemoto…858
19 Replacement of the collecting main of Hokkai No..5 coke oven S.Koizumi…859
20 Effect of coal maceral on the heating of coal by oxidation K.Matsudaira…860
21 Evaluation of fusibility of coal blend by using dynamic viscoelastic measurement T.Takanohashi…861
22 Effect of coal bulk density on coke properties(Development of coke strength estimation technology-4) T.Arima…862
23 Effect of the size of added plastic on coal carbonization S.Nomura…863
24 The operation results of waste-plastic recycling process using coke oven A.Sano…864
25 Control of CO2 reactivity and pore structure of coke H.Fujimoto…865
26 Effect of coke pore structure on coke strength after CO2 reaction K.Hanaoka…866
27 Effect of intense magnetic field on heat transfer around solidification front T.Kozuka…867
28 Control of molten steel flow in a continuous casting machine
by imposing static magnetic field parallel
to the slab width direction M.Morishita…868
29 The effect of electromagnetic vibration on collision and combine of inclusions S.Niwa…869
30 Effect of a high magnetic field on formation of carbonaceous mesophase spherules T.Torii…870
31 Effects of a high magnetic field on growth modes in vapor deposited films M.Ishihara…871
32 The removal of lead and nickel from copper with melting slag J.Shiino…872
33 The effect of H2 gas addition on the carburization of pure iron by CO R.Asano…873
34 Non-isothermal gravimetric investigation on kinetics of carbothermic reduction of chromium oxide K.Okumura…874
35 Effect of a supersonic jet on liquid surface D.Nakazono…875
36 Effect of high temperature field on the supersonic jet behavior I.Sumi…876
37 Acoustic cavitation assisted mixing of liquid in tank reactor M.Furukawa…877
38 Model experiment on ultrasound assisted decomposition of chemical substance in waste water N.Kawakita…878
39 Swirling flow effect in immersion nozzle in square billet continuous casting mold K.Sasaki…879
40 Suppression of mold powder entrapment in continuous casting
mold using immersion nozzle
with elliptic cross section J.Yoshida…880
41 Numerical prediction of microstructure evolution during
initial stage of solidification
using a phase-field model M.Ode…881
42 The phase field model for ternary alloys using regular solution approximation H.Kobayashi…882
43 Calculation model of growth of MnS precipitates in Fe-Si alloys H.Hasegawa…883
44 Effect of solute elements on the dendrite arm spacing in Fe-based alloys B.Wu…884
45 Influence of NaF addition to the system cuspidine-CaF2 H.Takahasi…885
46 Influence of Na2O on the equilibrium between mold flux composition and cuspidine M.Hanao…886
47 Fluorine elution from mold flux Y.Yamamoto…887
48 In-situ observation of argon bubble entrapment by soliditifying shell H.Esaka…888
49 Outline of national project on application of electromagnetic force to continuous casting of steel K.Ayata…889
50 Development of imposition technology of pulsative AC electromagnetic field in slab casting M.Tani…890
51 Flow control of molten steel in mold with super-conducting magnets Y.Kishimoto…891
52 Improvement of hot ductility in cotinuously cast strand by ferrite precipitation control Y.Itoh…892
53 Evaluation of mold flux consumption in continuous casting of steel based on cold model experiments S.Itoyama…893
54 Effect of the flux flow on the oscillation mark depth T.Ohkuma…894
55 Measurement of critical strain for formation of the transverse crack of ultra low carbon steel Y.Awajiya…895
56 Cause of scale-shaped crack formation by applying hot-scarfing K.Isobe…896
57 High temperature deformation behavior of peritectic carbon steel H.Mizukami…897
58 Influence of gas flow and deadman renewal on accumulation of fines on deadman surface K.Goto…898
59 Effect of slag solidification on mass and heat transfer phenomena in deadman T.Nishimura…899
60 Numerical analysis on unsteady heat transfer in lower part
of blast furnace taking account of melting
or re-solidification Y.Kashihara…900
61 Estimation of phenomena of burden descending in furnace by cellular automata method T.Imaizumi…901
62 Estimation of blast furnace slag viscosity at the time of solid-phase precipitation T.Orimoto…902
63 Prediction of carbon dioxide from blast furnace by using of the metallic burden T.Sato…903
64 Blast furnace operation of pulverized coal rate 210kg/T at Fukuyama Works M.Kuwabara…904
65 Flow behaviour of blast furnace taphole streams and their effect on trough refractory wear H.Qinglin…905
66 Effect of SiO2 on the reduction of CaO-containing wustite T.Inami…906
67 Gaseous reduction of iron oxide powder packed bet with H2-CO mixtures T.Yonezawa…907
68 Low temperature Moessbauer effect in χ-iron carbide F.Mase…908
69 Simulation regarding the mutual stimulate effect of
reduction and gasification
in iron ore-char composite pellet M.Hiura…909
70 Products during mechanical milling of iron oxide and graphite mixture H.Suzuki…910
71 Reduction behavior of hematite-graphite mixture with alkaline- earth metal oxide S.Kikuchi…911
72 Development of a ladle degassor J.Aoki…912
73 Re-oxidation behavior of molten steel by slag K.Fuchigami…913
74 Effect of slag properties on reduction rate of chromium in Cr2O3 containing slag by carbon in liquid metal K.Miyamoto…914
75 Construction of hot cyclone dust collector for chromium ore smelting reduction furnace S.Nabeshima…915
76 Influence of composition of refining slag on composition of inclusions in SUS304 slab Y.Ehara…916
77 Variation of inclusion composition in SUS304 stainless steel deoxidized with aluminum H.Todoroki…917
78 Deoxidation behavior in the creation of high
nitrogen-bearing stainless steel by pressurized ESR method
with Ca- bearing flux Y.Kobayashi…918
79 Effect of Al and O contents on the size distribution of alumina inclusions just after deoxidation M..Wakoh…919
80 Deoxidation equilibrium of Cr-Ni stainless steel with Si K.Suzuki…920
81 Phase equilibria between SiO2 and
iron-chromite solid solution,and deoxidation of liquid Fe-Cr
alloy
with Si T.Nagasaka…921
82 Thermodynamics on the FeO•Cr2O3 solid solution T.Nagasaka…922
83 Phase equilibria in CaO-MgO-FetO-P2O5 slag saturated with MgO T.Tamura…923
84 Activity measurements of Al2O3 and SiO2 in the Al2O3-SiO2-TiOX system M.Ohta••• 924
85 Determination of standard gibbs energy of formation of cuspidine by transpiration method H.Tabata…925
86 Affecting factors on the measurement of thermal diffusivity
of molten slag using double hot thermocouple
technique Y.Kashiwaya…926
87 Measurment of refractive indices for alkali silicate melts by ellipsometry T.Yagi…927
88 Examination of Faraday's law of electrolysis in reactions between Na2O-SiO2 melts and thermal plasma Y.Nakada…928
89 Viscosities of CaO-SiO2-Al2O3 slags N.Saito…929
90 Viscosity measurements and calculations for blast furnace type slags Y.Kita…930
91 Accurate prediction of the viscosities of steelmaking slags T.Iida…931
92 Influence of permeation water on bonding of blast furnace slag fine aggregate H.Mitsufuji…932
93 Investigation of attached organisms on carbonated
steelmaking slag
(Development of large carbonated steelmaking slag
blocks-7) T.Isoo…933
94 New compound K2Ca2Si2O7
contained in silicate fertilizer
(Development of slow- release potassium silicate fertilizer
with steelmaking slag-4) E.Hamada…934
95 Recovery of chromium from slags by Fe-C-Al-Si melts T.Nakasuga…935
96 Dissolution behavior of the constituents from converter slag K.Shitogiden…936
97 Stability diagram of nutritions dissolving from steelmaking slags into seawater T.Miki…937
98 Stability diagram of environmentally regulated elements dissolving from steelmaking slags into seawater T.Miki…938
99 Effects of MgO based glass addition on the dusting of
stainless steel slag
(Development of control process of stainless steel slag
dusing-3) N.Sakamoto…939
100 Atomization of slag-modeled melt by rotary cup atomizer T.Natsui…940
101 Promotion of pulverization by various rotary cup atomizers T.Mizuochi…941
102 Application of steelmaking slags to pile foundation A.Nishiwaki…942
103 Developement of EAF refining slag block Y.Kamiya…943
104 Adsorption property of nanometer particles by the carbonized RDF N.Akae…944
105 Thermite reaction of EAF dust with Al dross in insulated sleeve M.Mori…945
106 Dust recycling technology by dust treatment facilities at Kashima Steel Works T.Ookubo…946
107 Interface reaction and joining of ore with slag Y.Tsutsumi…947
108 Effect of flux composition on agglutination strength of hematite Y.Kuroki…948
109 Viscosity of primary formed melt in sintering process S.Machida…949
110 Development of estimation model for thermal properties of sinter K.Nishioka…950
111 Zone wize mineralogical characteristics of Marra Mamba type fine ores
(Characteristics of Marra Mamba type-iron ore-1) Y.Hida…
951
112 Assimilation properties of Marra Mamba iron ore
(Evaluation and technology for application of Marra Mamba iron
ore-2) J.Okazaki…952
113 Development of new granulation method adding the paper sludge T.Matsumura…953
114 Improvement of the sintering operation using the slitting plate of the upper layer T.Jinno…954
115 Improvement of sinter yield with adding coke breeze from the screw feeder M.Matsumura…955
116 Operation results of coke upper charging method at Kakogawa sintering plant S.Ishiwaki…956
117 Improvement of sinter yield at the surface layer of sintering bed S.W.Kim…957
118 Increasing productivity of No.5 sintering machine at NKK Fukuyama Works K.Yamashita…958
119 Effect of Cu in mixture on dioxin concentration in the
exhaust gas
(Behavior of dioxins in the sintering process of iron
ores-14) T.Kawaguchi…959
120 Measurement on the vertical distribution of copper content by
a quenching pot test
(Behavior of dioxins in the sintering process of Iron
ores-15) M.Nakano…960
121 In-site observation of reduction behavior of ironoxide by graphite using high temperature XRD method I.Seki…961
122 Temperature measurement on the reaction surface of an iron oxide-graphite facing pair M.Kanbe…962
123 Influence of the operating condition of HI-QIP on DRI productivity N.Ishiwata…963
124 Separation of Ni from laterite ore by sulfuric acid leaching H.Purwanto…964
125 Development of control system for hot metal process at Fukuyama Works S.Wakamatsu…965
126 Improvement of hot metal pre-treatment center in Chiba Works T.Yamauchi…966
127 Development of techniques for putting desiliconization flux into torpedos in advance H.Tsurumaru…967
128 Dephosphorization of Fe-C-P melts at 1623K by potassium ferrite Y.Sasaki…968
129 Effect of flux on dephosphorization of hot metal T.Murai…969
130 Effect of the feeding rate of iron oxide and hot metal
temperature on the hot metal dephosphorization rate
in torpedo car Y.Hino…970
131 Effect of hydrocarbon gas on hot metal desulfurization by CaO based flux N.Kikuchi…971
132 Numerical simulation of BOF top blowing jet Y.Tago…972
133 BOF refining technology for lhot metal with low manganese content J.S.Kim…973
134 Behavior of (T.Fe) in BOF slag Y.Kanzaki…974
135 Design of waste heat recovery system in a LD converter N.Maruoka…975
136 Measurement of oxidation of MgO-C refractories with thermobalance Y.Ayabe…976
137 Improvement of slab casting productivity at NKK Fukuyama Works K.Kameda…977
138 Simulation of sliding nozzle gate movements for steel continuous casting N.Kubo…978
139 Improvement of techniques for sequental casting of different
grade at Mizushima No.2 continuous casting
machine T.Takeda…979
140 Development of high quality steel production technique in the No.4 CCM at Kakogawa Works K.Sumida…980
141 The tendency for freckle formation in Inconel 718 K.Morita…981
142 Development of Ca less casting on 220⌈ middle bloom CC R.Kakimoto…982
143 Rockwool from municipal waste incinerator K.Yabuta…983
144 Kinetics on the carbon deposition from CO-H2-CO2 gas mixture with iron catalyst M.Nagaike…984
145 Factors affecting to the dioxins formation during oxidation of carbonaceous materials at low temperatures S.Kuzuhara…985
146 The effect of CO2 on properties of
charcoal absorbent from waste wood
(Synthetic utilization of waste wood by combination of smelting
of metal-6) T.Kitamura…986
147 Development of sludge recycling technology by 10t/d smelting
reduction furnace
(Development of recovery technology of valuable metal contained
in industrial sludge) T.Uchiyama…987
148 Behavior of zinc during smelting reduction of industrial
sludge by electric resistance furnace
(Development of recovery of metal contained value from
industrial sludge-7) K.Iwasaki…988
Social Engineering of Iron and Steel Industry
149 Engineering ethics and code of ethics for engineer K.Kuroda…990
150 Market trend forecast of iron material seen from social economy T.Hoshiba…991
151 Management analysis of iron and steel enterprise in fundamental industries K.Iwasaki…992
152 Analysis of competition power in electric furnace steel industries based on financial report H.Iwasaki…993
153 Rules and history of underground construction of Tatara furnace K.Nagata…994
154 The technology of cascade utilization of mixed fluoric-nitric acid for cleaning H.Uesugi…995
155 Analysis of CO2 emission from passenger cars by using a population balance model K.Kakudate••• 996
156 Co-production technologies into steel industry for reducing environmental impacts H.Yanagisawa…997
Current Advance in Materials and Process, Vol.14 ,No.5
Instrumentation, Control and System Engineering
157 Automatic diagram scheduling system for steel-making process S.Fujii…1000
158 Gain-scheduled tension and looper control in the hot strip finishing mill Y.Iijima…1001
159 Tension and looper control of hot strip mill based on CDM H.Ikeda…1002
160 Construction of advanced dust smelting furnace(The low cost design of the control device) S.Hirata…1003
161 Chamber wall condition measurement technique
(Development of wall roughness monitoring system in coke oven
chamber-1) T.Ashida…1004
162 Continuos molten steel temperature measurement using radiation thermometry M.Sugiura…1005
163 Development of continuous temperature analysis system in continuous casting process Y.N.Kim…1006
Production and Utilization Tecnology
164 Frictional coefficient in tube hydroforming and its effect on deformation M.Kojima…1008
165 Numerical simulation of the tube hydroforming process
(Friction effect on deforming behavior during hydroforming of
square cross section) M.Fukumura…1009
166 Effect of material properties on forming limit in tube hydroforming Y.Hashimoto…1010
167 Measuring methods and characteristic values of mechanical properties of tubes used for hydroforming Y.Shinohara…1011
168 Effects of strain on the microstructure formation of steel tube M.Aratani…1012
169 Improvement on inner surface quality of weldable 12%Cr seamless pipe T.Nakahashi…1013
170 New roll groove dressing machine of stretch-reducer T.Kimura…1014
171 Development of H-beam web off-center gauge M.Matsumoto••• 1015
172 Concentration analysis of lubricant additives for cold rolling by FT-IR A.Azushima…1016
173 Oil film and anti-seizure property in emulsion rolling T.Hirasawa…1017
174 Development of new rolling oil for tin gauge cold rolling S.Sugimoto…1018
175 Influence of hot rolling oil and rolling conditions on lubricated property T.Hiruta…1019
176 Practical application of roll seizure prevention technology with grease-type hot rolling lubricant H.Ihara…1020
177 Development of non-oil type lubricant for hot rougher rolling T.Inoue…1021
178 Warm rolling with lubricant in the vacuum condition Y.Yoshida…1022
179 Construction and operation of No.2 reheating furnace at NKK
Fukuyama No.1 hot strip mill
(Application of high temperature air combustion to a slab
reheating furnace-1) Y.Suzukawa…1023
180 Application of regenerative burner system to a large scale
slab reheating furnace
(Application of high temperature air combustion to a slab
reheating furnace-2) Y.Suzukawa…1024
181 Application of regenerative burner to a batch-type slab reheating furnace I.Mori…1025
182 Application of regenerative radiant tube burner to Fukuyama #3 continuous annealing line I.Mori…1026
183 Influences of temperature and atmosphere on the oxidation
behavior and descalability of SUS304
hot-rolled strip T.Oshima…1027
184 Effect of cooling rate and sintered carbon on mechanical
properties of nickel molybdenum pre-alloyed
powder H.Suzuki…1028
185 Several properties of Cu-W/Cu composite affected by infiltrating conditions T.Baba…1029
186 Fabrication of metal-alumina functional graded pipes by planetary slip casting H.Kobayashi…1030
187 Properties and microstructure of SiC ceramics that liquid face sintering were using HIP treatment Y.Mori…1031
188 Aluminizing of steel by liquid coating method K.Murakami…1032
189 High strengthening sintered Fe-Ni alloy steels H.Miura… 1033
190 Analysis on warm compaction behavior K.Kondoh…1034
191 Magnetic properties of flaky-shaped iron powder for dust cores N.Nakamura…1035
192 Eutectoid transformation originated from dispersed oxide particles K.Kasuya…1036
193 Characterization of cast strips for high P low-carbon steels K.Hirata…1037
194 Cast structure of high P low C steels cooled by several 10K/s T.Higuchi…1038
195 Influence of solidification mode on structure of continuously cast high phosphorus 0.1mass%C steel N.Yoshida…1039
196 Development of on-line control system for mechanical properties on the plate rolling mill H.Fujiuchi…1040
197 Development of predictive type FF-AGC in plate rolling S.Nishino…1041
198 Development of on-line control system for thickness,flatness and material property on plate rolling T.Tanemoto…1042
199 Development of on-line residual stress guarantee system of TMCP steel plate Y.Kobayashi…1043
200 In-situ observation of γ/α phase transformation in low carbon steel by laser microscopy T.Hanamura…1044
201 Relationship between thickness of pancake γ and thickness of grain boundary α S.Torizuka…1045
202 Effect of shear deformation on development of fine-grained ferrite structures T.Inoue…1046
203 Manufacture of duplex stainless steel large forging T.Wada…1047
204 Production of heavy section steel plates through forging and
plate rolling process using continuously cast
slabs-4 K.Araki…1048
205 Microstructural change by heavy deformation after reheating for cast slabs of 0.1mass% carbon steel T.Yamashita…1049
206 Mechanical properties of warm rolled steel plates with ultrafine-grained ferrite and cementite structures A.Ohmori••• 1050
207 Effect of diffusion of {100}parallel to the ND plane on the Charpy impact properties in low carbon steels T.Hanamura…1051
208 Fatigue properties of ultrafine-grained low carbon steels-2 T.Sawai…1052
209 Experimental investigation into characteristic of camber control in sheet bar rolling M..Eto…1053
210 Development of high response hydraulic looper in tandem hot strip mill A.Chamoto…1054
211 Development of high wear resistance cast iron roll with carbide enhanced matrix K.Hayashi…1055
212 Transcription mechanism of roll surface roughness on the strip surface T.Aono…1056
213 the edge-break phenomenon by skin pass rolling Ko.Hung.Suk…1057
214 Cutting characteristics of TiAl system intermetallic compounds H.Tagami…1058
215 Effect of ferrite morphology on delayed fracture properties
in high strength steel
(Improvement of toughness in high strength steel by thermo
mechanical treatment-1) J.Kodama…1059
216 Fatigue properties of high strength spring steel wire E.Abe…1060
217 Relationship between prior γ grain size and fatigue strength in high strength oil tempered wire H.Izumida…1061
218 Susceptibility of hydrogen in Si-enriched high carbon steel wire Y.Fujino…1062
219 Temperature analysis of a thin wire in fluidized bed patenting T.Hamada…1063
220 Effect of intermediate cooling after hot-deformation on the
proeutectoid cementite evolution at the grain
boundary in hyper-eutectoid steel rods S.K.Cho…1064
221 Effect of residual phase stress on the yield strength anisotropy for a ferrite-cementite steels T.Suzuki…1065
222 Development of dual phase steel for pitting resistant gears by surface hardening process K.Fukuoka…1066
223 Ultra smoothing bar by drawing process with protrusion die S.Kajino…1067
224 Decreasing residual stress by drawing process with protrusion die S.Kajino…1068
225 Effect of moisture absorption on drawability in steel wiredrawing K.Yosida…1069
226 Influence of straightening conditions on the longitudinal geometry T.Kuboki…1070
227 Influence of initial curvature of parent bar on the longitudinal geometry after drawing T.Kuboki…1071
228 Observation of process occurrennce in high-carbon steel wires N..Ito…1072
229 Prediction method of cracking limit in upsetting(Evaluation method for forgeability-1) S.Watanabe…1073
230 Influence of pre-deformation on crack limit in cold upsetting(Evaluation method for forgeability-2) S.Watanabe…1074
231 Influence of working condition on internal cracking occurence in cold extrusion K.Kuroda…1075
232 Bayesian neural network model for estimation of weld properties H.Fujii…1076
233 Development of prediction model for mechanical properties of large-heat-input SAW welds H.Fujii…1077
234 Effect of nitride precipitation on the HAZ toughness of high nitrogen containing Ni-free austenitic
stainless steel I.Woo…1078
235 Ultra-narrow gap GMA welding process for ultra-fine grained steels K.Hiraoka…1079
236 Deep penetration welding of ultrafine grained steel by 20 kW CO2 laser S.Tsukamoto…1080
237 Numerical analysis of deformation behavior for over-matched weld joints K.Nagai…1081
238 Mechanical properties of welded joints of ultra-fine grained steels H.Qiu…1082
239 Fatigue strength improvement of ultrafine grained steel
non-load-carrying cruciform welded joints
(Introduction of compressive residual stress with
low-transformation temperature welding wire) N.Suzuki…1083
240 Development of new explosive welding technique using
underwater shock wave for joining thin metal plate
onto steel K.Hokamoto…1084
Current Advance in Materials and Process, Vol.14 ,No.6
Microstructure and Properties of Materials
241 Formation of ultrafine grains during high temperature deformation of martensite in low-carbon steel N.Tsuji…1161
242 Formation of ultrafine grains in JIS-SS400 plain low-carbon
steel by conventional cold-rolling and
annealing of martensite starting structure R.Ueji…1162
243 Mechanical properties of ultrafine grained JIS-SS400 plain
low-carbon steel produced by conventional
cold-rolling and annealing of martensite starting
structure R.Ueji…1163
244 Ultra-grain refinement of JIS-SM490 steel by conventional
cold- rolling and annealing of martensite
starting structure N.Tsuji…1164
245 Change in microstructure and mechanical properties of 36%Ni
austenitic steel highly strained by ARB
process N.Tsuji…1165
246 Change in microstructure and mechanical property by annealing
of ultra-low carbon IF steel intensely
deformed to various strains by ARB N.Kamikawa…1166
247 Nanocrystallization in the surface region of carbon steels by high strain rate heavy deformation N.Suzuki…1167
248 Microstructure investigation on nanocrystallization process in carbon steels by heavy deformation Z.G.Liu…1168
249 Thermo-mechanical treatment for improvement of superplasticity on SUS304 M.Katoh…1169
250 Three-dimensional morphology and influence of Mo segregation
on the transformation behavior of
proeutectoid ferrite in an Fe-C-Mo alloy K.M.Wu…1170
251 Crystallography and interphase boundary structure of upper bainite T.Moritani…1171
252 Morphology and crystallography of intragranular ferrite
nucleated on incoherent MnS+V(C,N) complex
precipitate in austenite G.Miyamoto…1172
253 Crystallographical study of intra-granular ferrite in low alloy steel G.Shigesato…1173
254 Development of high HAZ toughness steel with fine microstructure imparted by fine particles R.Uemori…1174
255 Microstructure of degenerate pearlite in a hypoeutectoid Fe-C alloy K.Sakamoto…1175
256 Precipitation behavior of cementite during slow cooling in medium carbon steel M.Suzuki…1176
257 Investigation on the decomposition of cementite Z.G.Liu…1177
258 The effect of alloying additions on the properties of bulk cementite H.Takaoka…1178
259 The evolution of microstructure in vanadium microalloyed steels Y.Li…1179
260 Precipitation of fine particle sulfide in Fe-Cr-S alloys H.Mitsui…1180
261 Recovery of microstructure and mechanical property in aged duplex stainless steel H.Kuwano…1181
262 Magnetic properties of Fe-Cr-C,and Fe-Cr-C-Ni dual property magnetic materials S.Yokoyama…1182
263 Newly developed electrical steel for high frequency use M.Kawano…1183
264 Effect of boron on workability of 6.5%Si steel sheet K.Fujita…1184
265 The effects of S on magnetic properties of non-oriented electrical steel sheets Y.Oda…1185
266 Effect of frequencies of high-energy boundary in primary
recrystallized textures on secondary
recrystallization of the Goss grain M.Kurosawa…1186
267 Observation of grain growth process of secondary recrystallization in grain oriented electrical steel M.Komatsubara…1187
268 Dynamic observation of grain growth behavior by synchrotron
x-ray topography
(Effect of grain boundary character on selective growth of Goss
grain in Fe- 3%Si alloy-1) Y.Ushigami…1188
269 Motion of Goss boundary under pulsive heat treatment
(Effect of grain boundary character on selective growth of Goss
grain in Fe- 3%Si alloy-2) S.Takebayashi…1189
270 Features of texture of the adjacent primary grain to a Goss
grains in a secondary recrystallization in
Fe-3%Si alloy(Effect of grain boundary character on selective
growth of Goss grain in Fe-3%Si alloy-3) S.Nakamura…1190
271 Texture and size distribution of primary grains in the
vicinity of Goss boundary
(Effect of Goss boundary character on selective growth of Goss
grain in Fe-3%Si alloy-4) S.Suzuki…1191
272 Recrystallization texture formation of high-reduction cold rolled iron H.Homma…1193
273 Properties of the low carbon high nitrogen martensitic
stainless steel melted by a pressurized induction
furnace T.Koga…1192
274 Preparation of Fe-Cr-Mn stainless steel containing high nitrogen using mechanical alloying method R.Okabe…1194
275 Corrosion resistance of Fe-Cr-Mn-N steels produced by nitrogen absorption treatment at solid state M.Fujisawa…1195
276 Effects of N and Mo contents on localized corrosion
resistance of high N-bearing stainless steels
(Development of stainless steel for seawater
environment-7) M.Sagara…1196
277 Influence of Ca and S on corrosion resistance of super-low P SUS316L stainless steel S.Iwasaki…1197
278 Atmospheric corrosion resistance of ferritic stainless steels in marine environment K.Shirayama…1199
279 Effect of Cl and S content in synthetic ash on the corrosion
resistance of stainless steels to molten salts
(Corrosion resistance of stainless steels in waste incineration
environment-3) Y.Kawabata…1198
280 Effects of Si content on oxidation of SUS304 steels in steam at 1473K M..Hatano…1200
281 Effect of cooling condition on surface oxidation characterization of hot rolled SUS304 K.Tomimura…1201
282 Dissolution behavior of SUS430 with segregated phosphorus in sulfuric-nitric acid M.Tsuchinaga…1202
283 Technology to prevent surface defects of stainless wire rod to introduce of planetary cross rolling mill Y.Oikawa…1203
284 Hot deformation behavior with austenite grain size S.T.Hong…1204
285 The effect of Si content in the high temperature tensile test T.G.Kim…1205
286 Numerical simulation of phase decompositon in Fe-Cr binary and Fe-Cr-Mo ternary alloys Y.Suwa…1206
287 Phase separation in iron-based ternary alloys K.Ochi…1207
288 Grain growth in an (α+γ)region for Fe-Si-Cr-C-X alloys J.H.Park…1208
289 Relation between minor particle dispersion and grain sizes in stainless steels K.Takano…1209
290 The fiber components in the biaxially warm-deformed low-carbon steels F.Yin…1210
291 Texture development during cold rolling and annealing in two
type 304 stainless steel cast strips
(Texture development in strip cast type 304 stainless
steels-2) S.Teraoka…1211
292 Deformation history dependence of flow stress for a high nitrogen bearing austenitic stainless steel M.Kanda…1212
293 Effect of solid solution hardening on high speed deformation behavior for ferritic steels J.H.Park…1213
294 Effects of electrodeposited layers/Fe-substrate interface structures on mechanical properties K.Nakai…1214
295 Shape recovery characteristics of ferrous shape memory alloy wrapper tube at three points bending S.Mizote…1215
296 Probability and temperature dependence of cleavage fracture in steel M.Iwasaki…1216
297 Micromechanics analysis of charpy impact test Y.Haramiishi…1217
298 Constraint and size effects on ductility and toughness of Al alloys S.Kanamori…1218
299 Improvement of low temperature embrittlement in Hadfield steel Y.Ono…1219
300 Effect of stress-strain behavior on fracture toughness of ferritic steel T.Handa…1220
301 Significance of ductile crack at notch root on toughness of SM490A steel-2 E.Takeuchi…1221
302 Superconductor of the first kind S.Watanabe…1222
303 Superconductor of the second kind S.Watanabe…1223
304 Influence of Ni contents upon micro-structural changes due to rolling contact H.Nakajima…1224
305 Characteristics of the clean bearing steel melted in the atomosphere T.Kano…1225
306 Role of surface properties in pitting fatigue of carbo-nitrided steel T.Nakamura…1226
307 Influence of microstructure on wear and rolling contact fatigue behavior in rail steels H.Yokoyama…1227
308 Effects of copper and nickel contents on characteristics of cold-forging and aging steel T.Hanyuda…1228
309 Effect of hot deformation on hardness of Cu bearing extremely low carbon bainitic steel K.Hase…1229
310 The microstructures of Cu bearing extremely low carbon bainitic steels K.Hono…1230
311 Effect of grain size on bending strength of Ti or Ti-B doped carburizing steels H.Kinoshita…1231
312 FEM analysis of heat treatment distortions for carburized quenching products H.Imataka…1232
313 Effect of Mg and Ca addition on toughness and machinability
of resulfurized free-cutting steel
(Development of new resulfurized free-cutting
steel-1) N.Tsunekage…1233
314 Effect of S content and Mg and Ca addition on the
machinability and strength of steels
(Development of new resulfurized free-cutting
steel-2) K.Sato…1234
315 Improvement in cutting tool life by Mg+Ca addition in free-machining structural steels H.Yaguchi…1235
316 Effect of Si content and hardness on machinability of hot working die steels T.Fujii…1236
317 Precipitation behavior of fine MX type precipitates in HAZ of Cr-Mo steels M.Yuga…1237
318 Effects of thermo-mechanical processing on creep rupture
properties of MX precipitation strengthened
low- alloyed steels M.Ozaki…1238
319 Thermo-mechanical processing of MX precipitation strengthened
low- alloyed steels for improvement of
creep strength properties M.Kondo…1239
320 Reverse transformation of C-free martensitic steels K.Yamada…1240
321 Change in transient creep in Cr-Mo-V steel with stress D.Serino…1241
322 Analysis of stress relaxation behavior of 2.25Cr-1Mo steel based on creep deformation behavior T.Ohba…1242
323 Evaluation of creep crack propagation life at steam turbine rotor grooves M.Okazaki…1243
324 Fracture toughness of a retired high-intermediate pressure
steam turbine rotor
(Brittle fracture evaluation for the high and intermediate
pressure steam turbine rotor-1) H.Uemura…1244
325 AFM observation of fatigue crack initiation in strengthened low carbon steels Y.Sasaki…1245
326 Fatigue strength of ultrafine-grained steel(Fatigue of ultrafine-grained steel-1) K.Shirai…1246
327 Observation of fatigue crack initiation in ultrafine-grained steel(Fatigue of ultrafine-grained steel- 2) H.Miyata…1247
328 High-cycle fatigue properties of SUS304L electrogas arc welds at cryogenic temperatures T.Yuri…1248
329 Nanoscopic fatigue strength analysis of ferrite-pearlite steels and tempered-martensitic steels H.Hirukawa…1249
330 Giga-cycle fatigue properties for 1800MPa-class spring steel billets T.Abe…1250
331 Frequency effects on giga-cycle fatigue properties Y.Furuya…1251
332 High-cycle fatigue properties for modified-ausformed SCM440 steels-2 Y.Furuya…1252
333 Influence of steel surface property on galvannealing rate on galvanized steel sheet N.Fujibayashi…1253
334 Effect of substrate on the surface defect of galvannealed steel sheet S.Taira…1254
335 Frictional property of pre-phosphated galvannealed steel sheet T.Katagiri…1255
336 Electrodeposition of Zn-Al oxide composite from non-suspended solution K.Shouno…1256
337 Effect of inorganic additives in piclking solution on an electrodeposition of zinc on steel sheets S.Ando…1257
338 The improvement of stone chipping resistance and corrosion resistance of Zn-Ni alloy electrodeposition Y.S.Jeong…1258
339 Improvement of wet adhesion of tin free steel from the surfactant added bath T.Suzuki…1259
340 Influences of surface finish on the growth rate of oxide
films on titanium in atmospheric corrosion
environments N.Hara…1260
341 Effect of artificial fine Fe-rust on formative ability of
protective rust
(New surface treatment for promoting protective rust formation
on weathering steels-1) T.Komori…1261
342 Analysis of rust layer structure formed by atmospheric
exposure in airborne salt attacking environment
(New surface treatment for promoting protective rust formation
on weathering steels-2) W.Tanimoto…1262
343 Performance and application of new surface treatment to
actual structures
(New surface treatment for promoting protective rust formation
on weathering steels-3) T.Komori…1263
344 Corrosion behavior of coated weathering steel T.Matsumoto…1264
345 Corrosion behavior in each part of model structures expoused to outdoor H.Katayama…1265
346 Effect of environmental factor for corrosion of hot-dip galvanized tower steel K.Ono…1266
347 Properties of environmental purification of
photocatalyst-coated steel sheet
(Development of photocatalyst-coated steel
sheet-1) H.Nakamura…1267
348 Investigation on zirconia stabilizer in thermal barrier coatings(TBC) T.Torigoe…1268
349 Development of MoSi2 introduced thermal barrier coating K..Sonoya…1269
350 Effect of added ceramic on the Mn reaction resistance of thermal spray coating on hearth roll S..Midorikawa…1270
351 Observation of crack morphology after deformation of Ti film
deposited on goss single crystal
of silicon steel Y.Inokuchi…1271
352 Effect of γ-phase on the recrystallization behavior during hot rolling for 16%Cr ferritic stainless steels Y.Kato…1272
353 Effect of microstructure of hot rolled sheet for ridging of type430 stainless steel sheet J.Hamada…1273
354 Effect of grain diameter of hot bands on r-value of Nb bearing ferritic stainless steel sheets A.Miyazaki…1274
355 Machinability and corrosion resistance of Type 430 dispersed titanium carbo-sulfide K.Ishikawa…1275
356 Effect of sulfer content on continuous blanking workability of high strength austenitic stainless steel S.Suzuki…1276
357 3DAP characterization of tempered Fe-12.5r-15.5Co-2Mo-0.2C high strength stainless steel T.Honma…1277
358 Properties of weld joint of rolled thick plate made of the martensitic stainless steel for water turbine H.Kimura…1278
359 Effect of Si on properties of large-sized duplex stainless steel casting S.Tanaka…1279
360 Effect of Re on the solvus temperature of the laves phase in high Cr ferritic steels M..Kamiya…1280
361 Effect of Cr on the creep strengthening factor of ferritic
heat resistant steels
(The control of long- term creep strength degradation in the
high Cr steel-3) K.Miki…1281
362 Modeling of microstructure changes during creep based on the
phase-field method
(Application of the system free energy to the prediction of
microstructure evolution in high Cr heat
resisting ferrite steels-3) T.Koyama…1282
363 Effect of prior austenite grain size on creep deformation behavior in heat resistant martensitic steel Y.Nishihara…1283
364 Effect of boron on recovery and recrystalization behavior in heat resistant martensitic steels T.Kawamura…1284
365 Improvement of creep-fatigue life by heat treatment in high Cr ferritic steel Y.Hirakawa…1285
366 Effect of Co on creep deformation and precipitation behavior of high-Cr ferritic Steels Y.Kadoya…1286
367 Development and production of 10Cr1.5MoVNb steel for gas turbine compressor disk Y.Okamura…1287
368 Evaluation of long-term creep strength of high Cr ferritic
creep resistant steels from a viewpoint
of creep deformation K.Kimura…1288
369 Long-term creep strength and changes in creep deformation of high Cr ferritic creep resistant steels H.Kushima…1289
370 Effect of alloying elements on creep properties of Pd added 9%Cr steels H.Okada…1290
371 Softening behavior of high chromium ferritic steels during creep R.Ishii…1291
372 Effects of C and N on the creep strength properties of pecipitation strengthened 15Cr ferritic steels Y.Toda…1292
373 Effects of C and N on the mechanical property of precipitation strengthened 15Cr ferritic steels H.Tohyama…1293
374 Heat-to-heat variation in long- term creep strength of 12Cr-1Mo-1W-0.3V steel F.Abe…1294
375 Effect of MX type nitrides precipitated on boundaries in low-carbon 9Cr steel M.Taneike…1295
376 Effect of B addition on the creep strength in N free 12%Cr steels T.Azuma…1296
377 High-temperature high-cycle fatigue property of 12Cr-2W ferritic heat resistant steel K.Kobayasi…1297
378 Visualization of distribution of hydrogen during delayed
fracture in a martensitic steel at a 1500MPa tesile
strength level H.Shimoda…1298
379 Detection of deformation induced defects by hydrogen microprint technique T.Ohmisawa…1299
380 Visualization of hydrogen in stress-concentrated region of
SUS304 stainless steel by using Ag decoration
technique E.Akiyama…1300
381 Effect of deformation on hydrogen trapping of
dislocations
(Analysis of hydrogen trapping in high tensile strength
steel-2) D.Hirakami…1301
382 Evaluation of absorbed hydrogen distribution in the high
strength bolts tightened to various strength by
exposed test S.Sakashita…1302
383 Evaluation of absorbed hydrogen concentration in high
strength bolt by CCT simulating atmospheric
corrosion S.Sakashita…1303
384 Examination of experimental determination of the shape
parammeter m in the Weibull stress for evaluation
of the hydrogen embrittlement susceptibility of high strength
steel S.Takagi…1304
385 Evaluation of the hydrogen embirittlement susceptibility of high strength steel based on the local approach S.Takagi…1305
386 Evaluation of the hydrogen embrittlement for high strength steels with low diffusion coefficient of hydrogen T.Tsuchida… 1306
387 Strength and delayed fracture properties of martensitic steels containing Si,Cr and Mo Y.Kimura…1307
388 Evaluation of effect of vanadium and titanium on delayed fracture of SCM440 steel by SSRT W.Urushihara…1308
389 Delayed fracture properties of SCM440 steel with various
strength levels derived through modified
ausforming S.Terasaki…1309
390 Influence of prior austenite grain refinement on delayed
fracture properties of a 1400 MPa class high
strength steel Y.Kimura…1310
391 Hydrogen embrittlement susceptibility of grain-refined martensitic steel H.Fuchigami…1311
392 Mechanical properties of fully austenitic weld metal at low temperature
(Low temperature materials used in WE-NET 16) H.Okuno…1312
393 Cryogenic temperature toughness of reduced pressure electron beam weld metal
of austenitic stainless steels(Low temperature materials used in WE-NET 17) H.Nakagawa…1313
394 Fatigue properties of TIG welds of austenitic stainless steels in liquid hydrogen
(Low temperature materials used in WE-NET 18) H.Fujii…1314
395 Hydrogen environment embrittlement of SUS316 series
austenitic stainless steels at low temperatures
(Low temperature materials used in WE-NET 19) S.Fukuyama…1315
396 Effect of hydrogen charging on fracture toughness obtained by
small specimen of SUS304L steel weld
at cryogenic temperature(Low temperature materials used in
WE-NET 20) T.Ogata…1316
397 Change in back stress during creep deformation of austenitic steel M..Tamura…1317
398 Effect of S segregation and BN precipitation to creep cavities on creep rupture properties J..Kyono…1318
399 Microstructures in SUS304 for long term creep ruptured specimens in 723-973K M.Yamazaki…1319
400 Properties of a 18Cr-9Ni-W,Nb,V,N stainless steel tube after 2 year exposure in a power boiler T.Ishitsuka…1320
401 A role of γ��precipitates containing stacking faults in η phase evolution processes
in a 40Fe-29Ni-22Co-4Nb-2Cr-1Ti-0.5Al-0.5Si superalloy K.Kusabiraki…1321
402 Design of Ni-based superalloys with low thermal expansion-1 S.Isobe…1322
403 Design of Ni-based superalloys with low thermal expansion-2 R.Yamamoto…1323
404 Effect of aging time on mechanical properties and precipitation behavior of
Ni-16Cr-8.5Co-3.5Al-3.5Ti-2.6W-1.8Mo-0.9Nb alloy D.Saito…1324
405 Stress dependence of creep in Ni-20Cr alloy single crystal with [001] orientation Y.Nakamoto…1325
406 Creep in Ni-20Cr alloys single crystal with [011] orientation at lower stresses T.Yasui…1326
407 Orientation dependence of creep in Ta added Ni-20Cr alloy single crystal Y.Terada…1327
408 Relation between dislocation substructure and tensile
directions in single crystal Ni- - based superalloy,
CMSX-2,crept at 1273K-on [001] - [011] line- J.S.Lee…1328
409 Measurement of the density of super heat-resistance alloy at
liquid state and solid-liquid two-phase state
by a modified sessile drop method K.Mukai…1329
410 Change in dislocation substructure of oxide dispersion
strengthened Ni-based superalloy,MA754,with
creep deformation A.Takahashi…1330
411 Morphology of γ'phase of single crystal Ni-based
superalloy,PWA1480,serviced as 1st high pressure
turbine blade N.Harada…1331
412 Metallurgical Analysis of serviced CMSX2 single crystal gas turbine bucket-2 Y.Yoshioka…1332
413 Creep deformation of single crystal Ti-48at%Al alloy with fully lamellar structure M.Yoshida…1333
414 Collapsing of α2 plate in TiAl alloy with different orientation of lamellar plate to stress axis K.Kubushiro…1334
415 Creep of Ti-48Al with massive structure M.Yoshida…1335
416 Effect of acid rain on discoloration of titanium
(Discoloration mechanism of titanium in atmospheric
environments and development of preventive
method-1) M.Kaneko…1336
417 Effect of titanium carbide on discoloration of titanium
(Discoloration mechanism of titanium in atmospheric
environments and development of preventive
method-2) M.Kaneko…1337
418 Improvement of discoloration-resistance in commercially pure
titanium sheet
(Discoloration mechanism of titanium in atmospheric
environments and development of preventive
method-3) K.Takahashi…1338
419 Discoloration behavior of commercially pure titanium sheets
pickled in nitric-hydrofluoric acid solutions
(Discoloration mechanism of titanium in atmospheric
environments and development of preventive
method-4) K.Takahashi…1339
420 The effect of aluminum content on tensile properties and aging behavior of Ti-Fe-Cr-Al alloys M.Ikeda…1340
421 Effect of microstructure on fretting fatigue characteristics of Ti-4.5Al-3V-2Mo-2Fe J.Takeda…1341
422 Effect of βphase stability on mechanical properties in a β-rich α+β type titanium alloy Gunawarman…1342
423 Effect of oxide layer on wear characteristics of surface
oxidation treated biocompatible β-type titanium
alloy in simulated body environment S.Nakamura…1343
424 Microstructual evolution during high temperature deformation in β-titanium alloys Y.Touji…1344
425 Effect of heat treatment on mechanical properties of a heat resistant titanium alloy A.Suzuki…1345
426 Hot tensile behaviour of Mg alloy,AZ91-D S.Fudetani••• 1346
427 Effect of Mg on shape of zinc-phosphate crystal on electro- coated zinc H.Nakakoji…1347
428 Effect of sealing on the properties of Mg contained phosphated electrogalvanized steel sheet K.Hamahara…1348
429 Method to evaluate property of anti-finger printed steel sheets W.S.Jeong…1349
430 Effect of organic coatings on corrosion resistance of galvanized steel sheets N.Yoshimi…1350
431 Properties of various chromated 55%Al-Zn alloy coated steel sheets-3 A.Matsuzaki…1351
432 The effect of oxygen permeation through coating for cathodic
delamination of polyethylene coated steel
pipe M.Murase…1352
433 Effect of boron and chromium additions on the warm rolling behavior of low carbon steels J.J.Jonas…1353
434 Effects of Mo and B on hardenability after hot working H.Asahi…1354
435 Drawing behavior of pearlitic steel wire rods controlled by boron addition in medium carbon steel W.Y.Choo…1355
436 Effects of B and N on graphitization and hardenability in 0.53%C steels T.Iwamoto…1356
437 Investigation of boron distribution in martensitic 9%Cr creep resistant steel P.Hofer…1357
438 Improved utilization of added B in 9Cr heat-resistant steels containing W T.Horiuchi…1358
439 Effect of boron addition on structure and properties of low carbon bainitic steels W.Xuemin…1359
440 Role of boron in Improving creep rupture strength of ferritic heat resistant steels E.El- Kashif…1360
441 Influence of boron on toughness of quenched steel with various carbon contents M..Honda…1361
442 Effects of boron addition on tempering processes in an Fe-9Cr-0.1C alloy martensite S.Kobayashi…1362
443 Effect of boron on copper induced surface hot shortness of a carbon steel C.Nagasaki…1363
444 Effect of boron on the grain boundary segregation of
phosphorous and intergranular fracture in interstitial
free steels E.El- Kashif…1364
445 Determination of boron in steel by inductively coupled plasma
mass spectrometry after closed-vessel
microwave dissolution and anion exchange
separation K.Mizuno…1365
446 Effect of W on creep behavior of martensitic heat resistant steels M.Yoshizawa…1366
447 Effect of new thermomechanical heat treatment on microstructure of high-Cr ferritic heat resistant steels H.Okubo…1367
448 Long-term creep deformation characteristics in high-Cr ferritic steels M.Igarashi…1368
449 In-situ observation of recovery process in high chromium ferritic steel K.Sawada…1369
450 Effect of heat treatment on creep properties of 9%Cr ferritic steels K.Yamada…1370
451 Effect of high-temperature normalizing on creep strength of
simulated HAZ specimens of 9%Cr ferritic
steel M.Matsui…1371
452 Characteristic of crack propergation with martensitic stainless overlaied alloy Y.Satoh…1372
453 Type �W fracture on long term creep ruptured GTA welded joint specimen of 9Cr-1Mo-V-Nb steel plate T.Watanabe…1373
454 Effect of aging on creep strength of 11Cr-0.4Mo-2W-V-Nb-Cu steel A.Sasada…1374
455 Precipitation behaviour of Z-phase in mod.9Cr-1Mo steel during creep deformation K.Suzuki…1375
456 Steam oxidation behavior of carbon-free martensitic alloys H.Kutsumi…1376
457 Structure of steam oxidation scale on palladium containing high chromium ferritic steels T.Itagaki…1377
458 Effect of nickel content on creep properties of Fe-Ni-9Co-5Mo carbon-free martensitic alloys S.Muneki…1378
459 Carbon-free martensitic alloys with superior creep properties at high temperatures more over 973K S.Muneki…1379
460 Modelling of creep damage caused by particle coarsening
(Creep modelling of martensitic heat resistant
steels-2) H.Semba…1380
461 Effect of Si and P on the mechanical properties of cold rolled high strength TRIP steels S.J.Kim…1381
462 Effect of microstructure on the formation of retained austenite in C-Mn-Si steel T.Nakagaito…1382
463 The effects of thermomechanical processing on microstructure in low alloyed TPIP steels A.Hayakawa…1383
464 Effect of YAG laser cutting on stretch-flangeability of TRIP sheet steels A.Nagasaka…1384
465 Development of 590MPa grade precipitation hardening type
galvannealed sheet steel with superior spot
weldability K.Osawa…1385
466 Development of hot-rolled sheet steel with excellent strain-age hardenability S.Kaneko…1386
467 Measuring method of mechanical properties in impact tensile test T.Masuda…1387
468 Comparison between experiments and FEM simulation of high
velocity tensile test methods to clarify test
method's influence of high strength steel H.Yosida…1388
469 Effect of boron in solution on anisotropy of r-value of B-bearing Al-killed steel sheets Y.Funakawa…1389
470 Factors affecting texture memory appearing through α→γ → α transformation and its mechanism N.Yoshinaga…1390
471 Effect of hot-band's microstructure on texture formation of cold-rolled high carbon steel sheet N.Nakamura…1391
472 Effects of manganese on hot-ductility of low carbon steel T.Inoue…1392
473 Temperature of initiation of scale failure during cooling of low carbon steels S.Taniguchi…1393
Process Evaluation and Material Characterization
474 Direct determination of boron in iron and steel by reversed-phase high-performance liquid chromatography N.Uehara…1396
475 Determination of tellurium in steels by high power nitrogen
microwave induced plasma atomic emission
spectrometry coupled with hydride generation
method A.Matsumoto…1397
476 Application of the helium microwave induced plasma atomic
emission spectrometry to an analysis of
inclusion in iron and steel S.Tamura…1398
477 Estimation of rolling contact fatigue life due to
determination of non-metallic inclusions and impurity in
bearing steel K.Kizawa…1399
478 Quantitative evaluation of retained austenite in low carbon
TRIP steel sheet by saturation magnetization
measurement and EBSP method H.Akamizu…1400
479 Glow discharge optical emission spectrometry-activities and
opportunities in the field of depth profile
analysis A.Bengtson…1401
480 Characterising the RF plasma source in GD-OES R.Payling…1402
481 Some new advances in material analysis using plasma spectrometry Q.Jin…1403
482 Laser-induced breakdown spectrometry and its coupling with
low pressure ICP system for quantitative
elemental analysis Y.I.Lee…1404
483 Determination of Pb,Ag,Cu and Mn in steel by
electrothermal-atomic absorption spectrometry with direct
atomization of a solid sample,and shapes of absorption signals
based on atomization process of the
elements K.Takada…1405
484 Determination of antimony in steels by high power nitrogen
microwave induced plasma atomic emission
spectrometry with hydride generation T.Nakahara…1406
485 Rapid analysis of steel by ICP-AES and ICP-MS with laser ablation Y.Ishibashi…1407
486 Analysis of size distribution and chemical composition of oxides in steel by optical emission spectroscopy A.Yamamoto…1408
487 Present status of microstructural characterization of steel by analytical methods S.Suzuki…1409
488 Spectroscopic 2D observation of flames in an industrial furnace for steel processing K.Kitagawa…1410
489 Depth profiling of thin surface layers in
radiofrequency-powered glow discharge optical emission
spectrometry associated with amplitude modulation technique K.Wagatsuma…1411
490 The voids analysis of porous materials using NMR imaging and spectroscopy K.Saito…1412
491 Structural analysis of Al-containing compounds using MQMAS and CP/MQMAS NMR K.Kanehashi…1413
492 Analysis of the O-H groups in coals by infrared spectrometry Y.Fujioka…1414
493 Characterization of pyrolysis reaction of coal by generated gas monitoring M.Nishifuji…1415
494 Determination of vapor pressures of PCDD/Fs by Knudsen Method X.Li…1416