Program of the 149th ISIJ Meeting (March 29-31, 2005)
General Presentation Only


Current Advance in Materials and Process, Vol.18, No.1

High Temperature Processes

1 Evaluation of carbonization behavior of biomass in coke ovens K.Kato ……  87
2 Study of coal blending effect using high temperature imaging K.Saito ……  88
3 Influence of organic additives on the carbon growth rate from carbonization gas (Development of carbon deposition control technology in the coke oven -8) T.Nakagawa ……  89
4 Quantitative evaluation of defects in coke and effect of defects on coke strength
(Development of technology for producing high strength coke -1)		 Y.Kubota ……  90
5 Production of high strength and high reactivity coke by blending of agglomerated coal particles H.Fujimoto ……  91
6 Deformation behavior of coke cake during discharging S.Aizawa ……  92
7 Outline of the new type ceramic welding machine for coke oven chamber repair N.Takayama ……  93
8 Reinforcement of coal charge weight management system for coke oven K.Kojima ……  94
9 Analyses on dynamic solid flow in blast furnace lower part by deadman shape measurement Y.Matsui ……  95
10 Estimation of heat level in lower part of blast furnace in blowing-in operation T.Orimoto ……  96
11 Improvement of lower part permeability of blast furnace by injecting flux added waste plastics R.Murai ……  97
12 A behavior of MgO in high temperature zone of blast furnace T.Noda ……  98
13 Heat transfer analysis considering solidified layer generation in blast furnace hearth K.Nishioka ……  99
14 Inner state of blast furnace hearth corresponding to the change of bottom temperature (Analysis of liquid flow in blast furnace hearth -6) A.Shinotake ……  100
15 Measurement of iron and slag level with electromotive force in blast furnace hearth H.Yokoyama ……  101
16 Development of past similar data searching system using large scale database-based online modeling S.Matsuzaki ……  102
17 Numeral analysis on Si deoxidation equilibrium of molten Fe-Cr, Fe-Ni, Fe-Cr-Ni, Ni-Cu, Ni-Co alloys by quadratic formalism T.Miki ……  103
18 Interaction between silicon and molybdenum in molten iron D.Nakai ……  104
19 Two liquid phase separation of Fe-Cu-B ternary alloy K.Taguchi ……  105
20 Activities of phosphorus in copper, nickel and cobalt M.Hasegawa ……  106
21 B removal by Ti addition in the solidification refining of Si with Si-Al melt T.Yoshikawa ……  107
22 Effects of wettability on downward gas-liquid flow near the outlet of vertical circular pipe K.Fukushi ……  108
23 Surface tension of liquid Fe-Cr-O alloys with low oxygen content K.Yamamoto ……  109
24 Brief discussion on influences of surface active species on surface tensions of molten alloys T.Yoshikawa ……  110
25 Effect of surface orientation of alumina single crystals on the interfacial tension between molten iron and solid alumina under different oxygen partial pressures Joonho Lee ……  111
26 Improvement of bloom surface defects of high-aluminum alloy steels S.Takada ……  112
27 Prevention of longitudinal cracks of a continuously cast slab of an Fe-Ni-Cr super alloy containing Al
and Ti		 T.Ishii ……  113
28 Effect of alkali oxides on crystallization in CaO-SiO2-CaF2 glasses H.Hashimoto ……  114
29 Precipitation of Cu sulfide and MnS at high temperature in Fe-0.5%Cu-0.5%Sn super ultra low carbon steels K.Yamamoto ……  115
30 The effect of chemical content on MnS morphology in high S bearing steel T.Nishi ……  116
31 Agglomeration simulation of inclusions in molten steel based on fractal model Y.Sasaki ……  117
32 Analysis of blast furnace tap hole structure by numerical study of drilling speed M.Iida ……  118
33 Improvement of insulating refractories for the continuous reheating furnace H.Terashima ……  119
34 Development of dusting material to seal fine cracks in brickwork of coke oven chamber Y.Fukushima ……  120
35 The design technique of the Al2O3-C long nozzle suitable for long-time and repetition use S.Ito ……  121
36 Development and application of 'MOGUL' shaped submerged entry nozzle M.Ogata ……  122
37 Evaluation of low carbon magnesia-carbon bricks J.Yoshitomi ……  123
38 Development of used sliding-gate plates recycling M.Imanishi ……  124
39 Recycling used-sliding plate for Al2O3-SiC brick M.Hagiwara ……  125
40 Development of lining ripping robots for refractory maintenance T.Uchida ……  126
41 (Scientific Achievement Merit Prize)
Solidification of steel and its development		 M.Kudo
42 Effect of substrate radius on initial solidification H.Yamamura ……  127
43 Effect of surface properties of substrate on initial solidification M.Miyazaki ……  128
44 Undercooling and solidified microstructure in iron and nickel based alloys M.Tezuka ……  129
45 Microstructure control in carbon steel alloys with various phosphorus contents K.Igarashi ……  130
46 Evaluation of structure of molten Ca-Na-Si-Al-O-F system by MD simulation Y.Sasaki ……  131
47 Viscosity of Fe-Mo binary melt Y.Sato ……  132
48 Dependence of thermal conductivity for CaO-SiO2-Al2O3 slag on (%CaO)/(%Al2O3) ratio M.Watanabe ……  133
49 Temperature dependence of sound velocity in liquid metals of group XIV M.Hayashi ……  134
50 Difference in effects of alkali metal oxides on thermal conductivities of CaO-SiO2 slags S.Ozawa ……  135
51 Thermal conductivity measurements of some Al2O3-CaO-SiO2 molten silicates H.Ohta ……  136
52 Viscosity and structural analysis of CaO-SiO2-Al2O3-(R2O,RO) slags S.Sukenaga ……  137
53 Evaluation of surface tension of molten slag and ionic mixtures T.Tanaka ……  138
54 Non-axisymmetirc behavior of flow instability for oscillatory thermocapillary convection in molten silicon bridge at high Ma-numbers S.Shiratori ……  139
55 (Invited lecture)
Microwave heating and its applications		 T.Okamoto ……  140
56 Production of Ni particles by carbon reduction with microwave heating E.Ishizuka ……  141
57 Microwave heating with separated electric and magnetic fields in 2.45Ghz single- mode applicator N.Yoshikawa ……  142
58 Crystallization of BF slag by microwave irradiation K.Morita ……  143
59 Pig iron production from iron ore powder mixed with coal using microwave heating K.Ishizaki ……  144
60 Numerical analysis of fluid flow of arc plasma in tundish plasma heater N.Yamasaki ……  145
61 Flow patterns in thin slab continuous casting mold Baokuan Li ……  146
62 Development and evaluation of electromagnetically driven wideband ultrasonic oscillator (partU) M.Ohara ……  147
63 The crystal orientation taking account of gravity force under high magnetic field Cunyou Wu ……  148
64 Alignment of metal crystals using simultaneous imposition of static magnetic field and alternating current M.Usui ……  149
65 (Program for Stategic Research projects)
Numerical simulation on flow characteristics in double-axis electromagnetic stirrer		 S.Shimasaki ……  150
66 (ISIJ research promotion grant)
In-situ observation of growth and melting due to temperature change		 H.Esaka ……  151
67 Effect of wettability between mold surface and molten flux on mold heat transfer S.Itoyama ……  152
68 Investigation of thermal characteristics of mold powder below meniscus M.Terauchi ……  153
69 Numerical analysis on mold powder behavior with reynolds equation K.Okazawa ……  154
70 Experimental study on infiltration behavior of mold flux in continuous casting T.Kajitani ……  155
71 Analysis of the initial solidification on the Mold-flux Y.Kuroda ……  156
72 Improvement of bloom surface quality in the No.2 CCM at Kakogawa works K.Sumida ……  157
73 Prevention of slab surface transverse cracking at Kashima No.2 caster with surface structure control cooling(SSC) N.Baba ……  158
74 The improvement of surface cracks on case-hardening steel Y.Ohba ……  159
75 Prevention of surface crack caused by pinholes of low-carbon S-Pb free-cutting steel K.Isobe ……  160
76 (Nishiyama Commemorative Prize)
Mathematical simulation of iron and steel making processes		 K.Takatani ……  161
77 Rate of oxygen exchange reaction between CO2-CO gas and molten iron oxide Xiaojun Hu ……  162
78 Effect of alloying elements on evaporation removal rates of copper and tin from molten iron K.Taguchi ……  163
79 (Scientific Achievement Merit Prize)
Fluid flow and particle behaviors in liquid steel		 S.Taniguchi
80 Velocity of top-blown jet under vacuum pressure K.Naito ……  164
81 Behavior of particles and gas during flux injection in molten tin model N.Kikuchi ……  165
82 Shape change of molten metal droplet on substrate with ultrasonic vibration K.Okumura ……  166
83 Mineralogical properties of sedimentary type magnetite ore deposit in China
(Effective use of magnetite ore-5)		 Y.Hida ……  167
84 Ingredients analysis of iron ores using the infrared spectrophotometry Y.Fujioka ……  168
85 Evaluation of mineralogical properties of lump ores J.Okazaki ……  169
86 Effect of Al2O3 and MgO contents on liquidus for the CaO-SiO2-FeOx system
at various oxygen partial pressures		 K.Yajima ……  170
87 Measurement of sinter texture in rich limonitic ore ratio by image analysis M.Hoshi ……  171
88 Effect on sinter cake property and permeability by insertion of burning down content K.Ichikawa ……  172
89 Plant test of coke breeze and limestone coating granulation method for sinter mixture
(Development of coke breeze and limestone coating granulation technology-4)		 N.Oyama ……  173
90 Evaluation of sinter products by new coating granulation process in blast furnace
(Development of coke breeze and limestone coating granulation technology-5)		 N.Oyama ……  174
91 Presumed method of granulated particle character in dram mixer K.Yakashiro ……  175
92 Specificity of granulation of raw materials
(Development of the intensified granulation technique in iron ore sintering -7)		 T.Okada ……  176
93 Specificity of granulation with dispersant-2
(Development of the intensified granulation technique in iron ore sintering -8)		 K.Kono ……  177
94 Intensified granulation on raw material for higher bed permiability
(Development of the intensified granulation technique in iron ore sintering -9)		 O.Ishiyama ……  178
95 Operation of Oita No.2 sintering machine after improvement S.Furusyo ……  179
96 Development of a large amount of coke mixing charging into the blast furnace S.Watakabe ……  180
97 High productivity operation at Chiba No.6 blast furnace H.Okuyama ……  181
98 The recent operation at Kakogawa No.3 BF H.Toyota ……  182
99 Operation to protect hearth sidewall and improvement of blast balance at Kobe No.3 BF R.Tadai ……  183
100 Technology for extension of the blast furnace campaign life at Wakayama steel works T.Kobayashi ……  184
101 Long period shutdown for exchanging stave and start-up operation of Nagoya No.1 blast furnace D.Kato ……  185
102 Relining report of Oita No.2 BF(3rd) ver.1 (Blow-off operation and relining) M.Honda ……  186
103 Relining report of Oita No.2BF(3rd) ver.2 (Blow-in operation) T.Majima ……  187
104 Relining and blow-in of Keihin No.2(2nd) blast furnace K.Osada ……  188
105 (Nishiyama Commemorative Prize)
Advanced researches and developments in iron and steel making processes		 T.Yamamoto ……  189
106 (Nishiyama Commemorative Prize)
Blast furnace operation with low reducing agent ratio and recycle technology		 M.Naito ……  190
107 Simulation study of DME production using blast furnace I.Ooka ……  191
108 Influence of secondary pyrolysis of tar in coal on pre-reduction of iron oxide with coal carbonization gas N.Inoue ……  192
109 Microstructure of products during reduction of (Fe,Al)2O3 with CO-CO2 K.Takahashi ……  193
110 Influence of CaO on reaction behavior of coal char bearing iron ore composite pellets S.Hayashi ……  194
111 Conditions for completing the reduction of iron ore before 1000oC in moving-bed of blast furnace type Y.Iguchi ……  195
112 Effect of atmospheric gas composition on residual carbon in carbon composite briquet M.Kanayama ……  196
113 Reduction of iron oxide by using carbonized used paper Y.Kajita ……  197
114 Grinding swarf recycling to reduce environmental load
(No.2 Development of practical briquetting machine and test results) 		K.Nakamura ……  198
115 Development of waste tire recycling system in scrap melting furnace H.Kumazawa ……  199
116 Decomposition of CaSO4 with halide waste plastics Y.Hatakeyama ……  200
117 Chlorination and evaporation of PbO-PbCl2 melt with Ar-Cl2-O2 atmosphere H.Matsuura ……  201
118 Evaporation kinetics of metal chloride in the ZnCl2-PbCl2 system Canguo Wang ……  202
119 Reduction behavior of zinc oxide in the EAF dust Meng Fanming ……  203
120 Use of copper containing cast iron for keeping dust H.Katayama ……  204
121 Hydrothermal synthesis of zeolite A from iron and steelmaking slag and crystalline Al2O3 Y.Sugano ……  205
122 Classification of crystals precipitated based on the TTT diagram of BF slag T.Nakauchi ……  206
123 Influence of slag contents on the degree of slag expansion J.Nakashima ……  207
124 Solidification structure and redistribution of alloying elements in Inconel718 K.Yamamoto ……  208
125 Numerical prediction of solidification microstructure using a Multi-phase-field model M.Ode ……  209
126 Modeling of solid-solid phase transformations using Phase-field method T.Koyama ……  210
127 Phase selection of the austenite-dendrite and the two-phase dendritic-eutectec of an iron-carbon-chromium alloy T.Himemiya ……  211
128 Simulation of solidification structure formation during continuous-casting in Fe-C alloy M.Yamazaki ……  212
129 Simulation of solidification structure formation based on front tracking method M.Nakagawa ……  213
130 Introduction of plasma heater in Oita #1CC S.Yamada ……  214
131 Reoxidation mechanism of molten steel by plasma heating in tundish K.Sasai ……  215
132 Surface quality improvement of sheets by hot-cycle operation with one tundish S.Kooriyama ……  216
133 Control of molten steel flow in the strand with the application of M-EMS and S-EMS H.Harada ……  217
134 Development of new roll layout in high-speed casting
(Technology to attenuate periodical mold fluctuation-1) 		T.Murakami ……  218
135 Attenuation of mold level fluctuation caused by unsteady bulging with several frequency components
(Technology to attenuate periodical mold level fluctuation-2)
 		H.Kitada ……  219
136 Improvement of steelmaking productivity in Kakogawa works H.Takeuchi ……  220
137 Desulfurization behavior of hot metal in slag recycling process
(Development of desulfurization slag recycling process-1) 		Y.Nakai ……  221
138 Establishment of desulfurization slag recycling process(Development of desulfurization slag recycling process-2) R.Takehama ……  222
139 Effect of Mg gas injecting condition on the rate of hot metal desulfurization S.Mukawa ……  223
140 Thermit reaction assisted acceleration of slag formation during hot metal pretreatment M.Kuwabara ……  224
141 Scale-up of hot-metal container and direct charging to BOF S.Fujiki ……  225
142 Development of top and bottom blown converter with wide range of bottom gas flow rate (1) Y.Higuchi ……  226
143 Improvement of steel ladle refractories under high production N.Sakaguchi ……  227
144 Dephosphorization of liquid steel by BaO-CaO-FetO-CaF2 slags Wang Tao ……  228
145 Behavior of inclusions in deoxidation process of molten steel by in situ produced magnesium vapor T.Yamasaki ……  229
146 Deoxidation control for billet casting A.Kiyose ……  230


Social Engineering on Iron and Steel Industry

147 (Nishiyama Commemorative Prize)
Material flow accounting of steel procucts based on IO table in Japan 		K.Ishihara ……  249
148 Material flow of steel scrap in China
(Demand and supply of ferrous raw materials in China, Korea, Taiwan and ASEAN-1) 		S.Hayashi ……  250
149 Material flow of steel scrap in Korea
(Demand and supply of ferrous raw materials in China, Korea, Taiwan and ASEAN-2) 		S.Hayashi ……  251
150 Material flow of steel scrap in Taiwan
(Demand and supply of ferrous raw materials in China, Korea, Taiwan and ASEAN-3) 		S.Hayashi ……  252
151 Material flow of steel scrap in ASEAN
(Demand and supply of ferrous raw materials in China, Korea, Taiwan and ASEAN-4) 		S.Hayashi ……  253
152 The estimation of steel accumulative amount classified by usage sections in Japan W.Tamaki ……  254
153 Analysis on scrap generation and Cu concentration associated with cyclic use of steel in Japan by using a dynamic model I.Daigo ……  255
154 A life cycle inventory model for material transportation Yinghao, LIU ……  256
155 Effect of the size for small tatara steelmaking furnace E.Yamasue ……  257
156 Effect of crystalline phase on color tone of glaze for celadon T.Watanabe ……  258
157 Mechanical properties of Cu bearing steel J.Ohsawa ……  259


Social Engineering on Iron and Steel Industry/Environmental and Energy Technology

158 Construction of model society using green hydrogen in the Honjyo-Waseda area H.Uesugi ……  260
159 Development of apparatus for production of high pressure hydrogen from aluminum waste and aqueous solution T.Hiraki ……  261
160 Combustion synthesis of hydrogen storage alloys I.Saita ……  262
161 Development of fuel cell traffic-signal system using green hydrogen T.Takano ……  263
162 (Invited lecture)
Utilization of hydrogen-releasing tablets for medical, health and mobile-polymer electrolyte fuel cell 		N.Tsuji ……  264
163 Decomposition of biogas into hydrogen on hot slag Hadi Purwanto ……  265
164 Fixation of sulfur and hydrogen production from hydrogen sulfide by using goethite T.Nakamura ……  266
165 Fundamental study on sulfur recovery and hydrogen production from oil by using metal containing waste E.Shibata ……  267
166 Consideration concerning the introduction of hydrogen and fuel cell technologies for environmental load suppression in Tohoku district K.Yamaguchi ……  268
167 Combustion synthesis of lanthanum gallate type electrolyte in solid oxide fuel cells H.Ishikawa ……  269
168 Preparation of hydrogen storage alloys by calciothermic reduction of oxide mixture R.Suzuki ……  270
169 Embrittlement and fatigue properties of stainless steels in high-pressure hydrogen gas M.Miyahara ……  271
170 Whole outline of hydrogen amplification technology development using a by-product gas in the steel making processes(hot COG) as a source(Hydrogen amplification technology development using a by-product gas in the steel making processes(hot COG(Coke Oven Gas)) as a source-1) H.Nagahama ……  272
171 Hydrogen production by partial oxidation and steam reforming of hot coke oven gas
(Hydrogen amplification technology development using a by-product gas in the steel making processes(hot COG(Coke Oven Gas)) as a source-2)
 		T.Hashimoto ……  273
172 (Invited lecture)
Cold-model simulation of gas mixing in tar-converter head
(Hydrogen amplification technology development using a by-product gas in the steel-making processes (Hot-COG (Coke Oven Gas)) as a source-3) 		K.Kurihara ……  274
173 (Invited lecture)
Combustion simulation around mixed-gas injection nozzle in tar-converter head
(Hydrogen amplification technology development using a by-product gas in the steel-making processes (Hot-COG (Coke Oven Gas)) as a source-4) 		M.Inoue ……  275
174 Development of reforming catalyst for COG
(Hydrogen amplification technology development using a by-product gas in the steel making processes(hot COG(Coke Oven Gas)) as a source-5) 		K.Suzuki ……  276
175 Oxygen separation from compressed air using ion conducting materials (Hydrogen amplification technology development using a by-product gas in the steel making processes (hot-COG(Coke Oven Gas)) as a source-6) W.Ito ……  277
176 Development of oxygen separating process using mixed ionic-electric membrane
(Hydrogen amplification technology development using a by-product gas in the steel making processes (hot COG(Coke Oven Gas)) as a source-7) 		M.Asanuma ……  278
177 Structural analysis of ion conducting materials using NMR (Hydrogen amplification technology development using a by-product gas in the steel making processes (hot-COG (Coke Oven Gas)) as a source-8) K.Kanehashi ……  279
178 Development of ceramic membrane reactor system(Hydrogen amplification technology development using a by-product gas in the steel making processes(hot COG(coke oven gas))as a source-9 H.Kurimura ……  280


Environmental and Energy Technology

410 Effect of iron oxide and carbon catalyses on the methane hydrate formation under stirring conditions M.Takahata ……  282
411 Decomposition of CO2 with mechanically-milled magnetite H.Yamaguchi ……  283
412 Characteristic feature of chinese steel production and its tentative identification N.Katagiri ……  284
413 Boron elution from stainless steel slag K.Kakimoto ……  285
414 Removal of harmful metal in wastewater and recovery of value metal
Removal of As in wastewater(1st report) 		F.Noguchi ……  286
415 Treatment of wastewater with oil using a gas-liquid two-phase swirling jet M.Shitara ……  287
416 Reusing process of rice husk ash via solid-state synthesis K.Kondoh ……  288
417 Separation and recovery of phosphorus from steelmaking slag with strong magnetic field T.Nagasaka ……  289


Environmental and Energy Technology/Microstrucrure and Properties of Materials

418 (Invited lecture)
Trends in advanced coal-fired power plants and r & d of high temperature materials
(1. Advanced coal-fired power plants and increase of steam temperature) 		F.Masuyama ……  290
419 (Invited lecture)
Trends in advanced coal-fired power plants and r & d of high temperature materials
(2. Materials issues with higher temperature and alloy development) 		F.Masuyama ……  291
420 (Invited lecture)
Current technology and future challenge of material for ultra super critical coal fired boilers 		M.Kitamura ……  292
421 Next generation USC-Plants employed 700 degree C steam H.Nakagawa ……  293
422 Materials issues for advanced USC boiler plant N.Komai ……  294
423 Alloy designing of 9Cr steel for welded pipes in USC boilers at 650°C F.Abe ……  295
424 Trends and problems of development for 700°C USC turbine rotor material T.Azuma ……  296
425 Creep rupture strength of Alloy617 weldment as a candidate material
for next generation USC boiler components 		T.Sato ……  297
426 Development of Fe-Ni base austenitic alloys for piping in 700°C USC power plants H.Okada ……  298
427 Orientation dependence of grain boundary fracture in SUS316 steel at high temperature M.Mitsuhara ……  299
428 Creep properties and microstructure of simulated HAZ of boron contained 9%Cr heat resistant steel M.Shimizu ……  300
429 Microstructural factor of the type IV damage at a heat affected zone of weld for ferritic heat resistant steels with high Cr content Y.Hasegawa ……  301
430 Microstructure of 9% Cr-W ferritic heat resistant steel used for long-term actual plant service T.Muraki ……  302
431 Effects of carbides and carbonitrides on long-term creep characteristics of high Cr ferritic steels M.Igarashi ……  303
432 Specification of inclusions in high Cr ferritic heat resistant steel K.Sakuraya ……  304
433 Creep properties of carbon-free Fe-12Ni-9Co-5Mo-5Cr martensitic alloys S.Muneki ……  305
434 Degradation of long-term creep strength in low-N 9Cr heat resistant steels H.Semba ……  306
435 Prediction of long-term creep rupture strength for 12Cr creep resistant steels in consideration of bending K.Kimura ……  307



Current Advance in Materials and Process, Vol.18, No.2


Instrumention,control and system Engineering

179 Frequency properties of flow in dual in-mold electromagnetic stirring R.Hirayama ……  326
180 Application of walking control technology using walking sensor
(Development of walking control technology in hot strip finishing mill-4)
 		Y.Buei ……  327
181 Stabilizing control of hot rolled strip tension at the start of coiling using frequency-shaped sliding mode control T.Shimamura ……  328
182 Development of elongation control for skin pass mill T.Ueno ……  329
183 Estimation of heat transfer coefficient at water-cooling process of plates K.Sugiyama ……  330
184 Slab detecting system of high performance cooling type YoungJu Kang ……  331
185 Development of plate length meter for hot plate finishing mill Y.Isei ……  332
186 Development of high speed continuous profile measurement system Y.Konno ……  333
187 Development of the coil position sensing device for automatic cranes H.Sugiura ……  334
188 Surface flaw testing by rotating uniform eddy current probe K.Koyama ……  335
189 Eddy current flaw testing of steel material by plus probe Y.Tanaka ……  336
190 High resolution ultrasonic detection of internal flaws in deep position by combination of focused beam testing with synthetic aperture technique (SwiFT) H.Takada ……  337
191 Optimization of production loads for plural reactor furnaces in case of demand change K.Ishimaru ……  338
192 Large scale database-based online modeling on blast furnace operation M.Ito ……  339
193 New process computer system of No.2 steel making plant in West Japan Works(Kurashiki) T.Goto ……  340
194 An autonomous decentralized scheduling system for aluminum production line T.Miyama ……  341
195 Application of ubiquitous technology to the process automation in iron-and steel making S.Shimoi ……  342


Processing for Quality Products

196 Effect of micro segregation on the internal properties of drawing wire K.Kikuchi ……  401
197 Effects of slab width on deformation in rolling of ultra thick H-beams H.Ishibashi ……  402
198 FEM analysis of long product using two step meshing method
(Development of the modern interface for FEM analyses of plastic workings-4) 		T.Yoshida ……  403
199 Warm and hot bending of high strength steel sheets using resistance heating K.Mori ……  404
200 Springback of high-strength steel after hot and warm sheet formings-2 K.Oyamada ……  405
201 Effects of material model on spring back simulation E.Isogai ……  406
202 Deep drawing square cups of titanium sheet by the tools with beads S.Kurihara ……  407
203 (Nishiyama Commemorative Prize)
Steel solution for crashworthiness and weight reduction through application of advanced high strength steel 		Y.Kuriyama ……  408
204 Effect of heat treatment on bending angle in laser forming of pure titanium foil M.Otsu ……  409
205 (ISIJ research promotion grant)
Producing method of metallic hollow sphere by precision press forming from sheet metal 		H.Yoshimura ……  410
206 (Mishima Medal)
Development of innovative manufacturing technique and products in steel tube and pipe making 		T.Toyooka
207 Improvement of size availability with medium-diameter seamless steel pipe mill S.Nambu ……  411
208 Improvement of size availability with 26" ERW pipe mill T.Koide ……  412
209 Extension of range manufacturing steel tubes in 4 inch ERW mill with 4 roll type reducing mill Y.Takemura ……  413
210 The effects of the oxide scale on the lubricity during hot rolling (I) S.Iida ……  414
211 FEM simulation of rubber bulge processing of steel tube H.Yoshimura ……  415
212 Discussion on the burst pressure in T-shape hydroforming H.Hishida ……  416
213 Numerical simulation of three-dimensional free surface flow
(Deformation behavior of a drop impacting obliquely on a solid surface) 		H.Fujimoto ……  417
214 The relationship between impinging jet pressure and cooling rate in the water cooling R.Yamamoto ……  418
215 Effect of the water pool on the spray cooling Y.Serizawa ……  419
216 Measurement of transformation super-plasticity deformation in plate cooling Y.Serizawa ……  420
217 Analysis of effect of the different roll speed rolling on warp of sheet Y.Higashida ……  421
218 Heavy cold leveler K.Hashimoto ……  422
219 On-line roll grinder for plate mill T.Honda ……  423
220 Transferring roll roughness to the rolled strip in skinpass rolling Y.Aramaki ……  424
221 Effect of the skinpass rolling lubricant on roll surface transcription in skinpass rolling process by dull roll N.Nagase ……  425
222 Effect of surface profile of roll on surface gloss of rolled sheets and friction coefficient in cold rolling of stainless steel H.Ikuta ……  426
223 Development of precision rolling method M.Yamagata ……  427
224 Mechanical properties and the method improving them in laser welded ultra fine grain steel T.Otani ……  428
225 Microstructure evolution in HAZ of laser welded ultrafine grained steel S.Tsukamoto ……  429
226 Characteristics of welded joints of UFG steels K.Hiraoka ……  430
227 (Invited lecture)
Metallurgical and mechanical properties of friction stir welded ultra fine grained steel 		S.Hirano ……  431
228 Low temperature diffusion bonding for ultrafine grained steels S.Nanba ……  432
229 Microstructure and deformation of austenitic stainless steel SUS310S in semi-solid state Jingyuan Li ……  433
230 Semi-solid state extrusion of steel alloy-2 S.Sugiyama ……  434
231 (ISIJ research promotion grant)
Effects of welding speed, current, arc length on weld shape in advance A-TIG (AA-TIG) 		H.Fujii ……  435
232 (Nishiyama Commemorative Prize)
Development of prediction method on microstructure of 490MPa weld metal 		Y.Seki ……  436



Current Advance in Materials and Process, Vol.18, No.3


 Microstructure and Properties of Materials

233 Nano-meso-macro strength analysis of low-cycle fatigued SUS304 stainless stee N.Nagashima ……  465  
234 Ultrasonic fatigue testing for high-strength steel under tensile mean stress Y.Furuya ……  466
235 Nano-Meso-Macro strength analysis of low-cycle fatigued fine- and coarse-grain ferritic steels S.Matsuoka ……  467  
236 Effect of stress ratio on fatigue properties for Ti-6Al-4V alloy (900MPa class) E.Takeuchi ……  468
237 Effect of stress ratio on fatigue properties for high strength steels T.Abe ……  469
238 Evaluation of the influence of hydrogen on fatigue properties of SUJ2 bearing steel by ultrasonic fatigue testing Y.Matsubara ……  470
239 Influence of non-metallic inclusion size on rolling contact fatigue life M.Nagao ……  471
240 Observation of fatigue crack initiation process in SUS304 steel with AFM Y.Nakai ……  472
241 (ISIJ research promotion grant)
Three-dimensional fractography using fractal dimension map (FDM) and surface roughness map (SRM) 		M.Tanaka ……  473
242 Effect of inclusion on magnetic property of Ni-Mo-Cu-Fe alloys K.Umehara ……  474
243 Magnetic properties and recrystallization textures of phosphorus-added non-oriented electrical steel sheets I.Tanaka ……  475
244 Effect of forsterite coating of grain oriented steel on the high frequency iron loss T.Okubo ……  476
245 Influence of tensile stress and surface state on magnetic properties in 3%Si-Fe single crystals-2 S.Okabe ……  477
246 Relationship between strain distribution and magnetic domain refining
in laser-irradiated Fe-3%Si single crystal 		M.Imafuku ……  478
247 Recrystallization of -fiber in 3.5% Si-Steel S.Nakamura ……  479
248 Texture formation during strain induced boundary migration in electrical steel sheets K.Murakami ……  480
249 Effect of precipitations on the recrystallisation texture of cold rolled 3%Si-Fe {110}<001> single crystal -EBSP analysis- N.Morishige ……  481
250 Influence of primary recrystallization texture through thickness to secondary texture on grain oriented silicon steel T.Kumano ……  482
251 Development of YS500N/mm2 high strength offshore structural steel
with good CTOD properties at welded joints 		Y.Nagai ……  483
252 Development of a 590N/mm2 grade steel plate with an excellent HAZ toughness for architectural constructions K.Ueda ……  484
253 Properties of low-Pcm type large-heat-input weldable steel for bridge-building-use T.Hada ……  485
254 Development of 9%Ni steel plates with superior low temperature toughness for LNG storage tanks M.Hoshino ……  486
255 Toughening of low yield strength steels by controlling excess carbon content with Ti addition Y.Watanabe ……  487
256 (Mishima Medal)
Microstructural aspects in fracture of high strength-high toughness materials 		K.Nagai
257 (ISIJ research promotion grant)
Effects of parallelism of slip systems between bainite laths on their deformation behavior 		H.Okubo ……  488
258 Investigation of cyclic softening of the high-strength steel HT80 using positron annihilation lifetime spectrometer M.Yoshida ……  489
259 FEM-MD Combined method considering grain boundary slip for evaluation of strength properties of steels R.Higuchi ……  490
260 (Program for Stategic Research projects)
What can we measure by neutron scattering for steel engineering development? 		Y.Tomota ……  491
261 (Program for Stategic Research projects)
Tetoragonality of martensite in carbon bearing steels 		Y.Tomota ……  492
262 (Program for Stategic Research projects)
Microstructural features of a heavily drawn pearlite steel wire 		Y.Shiota ……  493
263 (Program for Stategic Research projects)
Determination of volume fraction and carbon concentration of austenite in TRIP-aided multi-phase steels by neutron TOF diffraction 		S.Chen ……  494
264 (Program for Stategic Research projects)
Recovery and recrystallization behavior of a ferrite steel subjected to heavy plastic deformation 		T.Suzuki ……  495
265 (Program for Stategic Research projects)
Development of in-situ neutron diffraction measuring system during hot deformation using direct resistance heating 		T.Suzuki ……  496
266 (Program for Stategic Research projects)
Residual stress measurement by neutron diffraction for a SUS 304 mechanical component 		S.Jin ……  497
267 (Program for Stategic Research projects)
Effect of nitrogen addition on tensile behavior of austenitic stainless steels studied by neutron scattering 		K.Ikeda ……  498
268 (Program for Stategic Research projects)
Multi-scaled heterogeneity in plastic flow of pearlite steels 		S.Morooka ……  499
269 (Program for Stategic Research projects)
In situ TOF neutron diffraction during tensile loading for an ultra-heavily drawn pearlitic steel wire 		Y.Shiota ……  500
270 Development of the image processing designed steel sheet with excellent
formability 		K.Koshiishi ……  501
271 Investigation of cathodic disbonding test in consideration of cathodic protected polyethylene lining steel for maritime structure T.Yamazaki ……  502
272 Long term durability of organic protective coatings for maritime structures
(Analysis of corrosion under protective layers) 		M.Yamamoto ……  503
273 Relationship between curing behavior of paint film and solvent popping occurrence H.Kanai ……  504
274 Observation of phosphate crystals inside blisters under corrosive condition K.Yuasa ……  505
275 Results of the 10-year weathering tests of prepainted steel sheet by roof-wall simulated specimen-2 Weatherability of paint H.Nomura ……  506
276 (Nishiyama Commemorative Prize)
Stability of BCC ordered phase in X-Al (X:3d-transition elements) binary systems 		R.Kainuma ……  507
277 (ISIJ research promotion grant)
Thermodynamic assessment of phase equilibria in the Fe-Rh-Ti ternary system 		I.Ohnuma ……  508
278 Thermodynamic analysis of the Fe-Nb-P ternary system N.Hanaya ……  509
279 Carburization mechanism of case hardenning steels in vacuum carburizing process T.Morita ……  510
280 Modeling Cu precipitation at multiple sites in Fe-Cu alloys J.B.Yang ……  511
281 Modelling precipitation of V4C3 carbide in a martensitic steel S.Yamasaki ……  512
282 Modelling of bainite transformation with sheaf-size and nucleation site K.Hayashi ……  513
283 Effect of thermal history on austenite-ferrite transformation in boron-nitrogen added steel M.Minagawa ……  514
284 Spatially resolved in-situ observation of solidification and phase transformation in low-alloy steel welds using synchrotron radiation H.Terasaki ……  515
285 (Scientific Achievement Merit Prize)
Changes in creep deformation and fracture mechanisms and their influence on prediction of long-term creep properties 		K.Maruyama
286 Metallographic atlas of the three type 2.25Cr-1Mo steels with different initial microstructure H.Kushima ……  516
287 Evaluation of mobile dislocation density of 2.25Cr-1Mo steel by stress change test in creep deformation H.Hayakawa ……  517
288 Properties of repair weldments of a CrMoV steel casting after long time service M.Okazaki ……  518
289 Improvement of the steam oxidation resistance for 9Cr heat resistant steels by pre-oxidation in low-oxygen argon H.Kutsumi ……  519
290 Effect of pre-oxidation temperature and Si content on steam oxidation behavior of 9Cr ferritic steels O.Yoshida ……  520
291 Creep rupture strength of pre-strained austenitic stainless steels N.Saitoh ……  521
292 Stress to produce a creep rate of 0.01%/1000h and stress to cause rupture at the end of 100,000 h for heat resistant steels and alloys F.Abe ……  522
293 Effect of strain rate on elastic property at high temperature in ferritic heat resistant steels K.Sawada ……  523
294 Change in micro-structural parameters,EOS and C,for 8Cr-2W steel during creep M.Tamura ……  524
295 Prediction of the precipitation evolution in high Cr heat-resistant ferritic steels during tempering by the system free energy concept T.Kunieda ……  525
296 Effect of microstructure on creep deformation characteristics of martensitic steels M.Yoshizawa ……  526
297 Effects of boron addition on microstructure evolution during creep of 0.1C-9Cr-3W-3Co steels S.Kobayashi ……  527
298 Effect of thermomechanical heat treatment under magnetic field on the long term creep properties and microstructures of a high-Cr ferritic heat resistant steel H.Okubo ……  528
299 Effect of MX carbonitrides on creep rupture strength of 9Cr ferritic steels S.Shimoyama ……  529
300 Influence of isothermal holding after normalizing on precipitation behavior of MX carbonitride M.Yoshino ……  530
301 Theoretical analysis on phase equilibria of MX carbonitrides in 9Cr-V-Nb steel Y.Toda ……  531
302 The relationship between material character and member strength at high temperature N.Matsuishi ……  532
303 (Nishiyama Commemorative Prize)
Production and coating of Ti in slag and molten salt 		T.Takenaka ……  533
304 Direct thin titanium plate lining technology for steel structures(Part3) H.Terashi ……  534
305 Effect of Al addition on aging behavior in Ti-1.2Fe-12.8Cr-Al alloys M.Ogawa ……  535
306 Deep drawability of pure titanium sheet by plastic die Y.Harada ……  536
307 Caulking by shot peening Y.Harada ……  537
308 Wetting properties of ceramics in various liquids T.Tokuda ……  538
309 (ISIJ research promotion grant)
Damping capacity of hexagonal boron  nitride-dispersed composite steel 		S.Horinouchi ……  529
310 The quality of sheared surface in high-strength steels R.Okamoto ……  540
311 Effect of blanking tool hardness on hole expanding ratio of high-strength hot-rolled sheet H.Tanahashi ……  541
312 Crack propagation on sheared edge in hole expansion test of hot-rolled high tensile strength steel sheets
(Analysis of dominant factor of hole expansion ratio of hot-rolled high tensile strength steel sheets-1) 		Y.Takahashi ……  542
313 Effects of chemical composition on resistance weld properties in 780MPa class steel sheets for ERW tube S.Toyoda ……  543
314 Influence of alloying elements on mechanical properties of Cu-added steel
(Nitriding processes of Cu-added steels-1) 		K.Kawasaki ……  544
315 Three-dimensional atom probe analysis of Cr- and Cu-added nitriding steels
(Nitriding processes of Cu-added steels-2) 		J.Takahashi ……  545
316 The effect of the atmospheres on the enriched copper at the scale/metal interface during high temperature oxidation of a steel containing copper-3 Y.Kondo ……  546
317 Relationship between mechanical properties and microstructure in high speed plastic deformed low C steels Y.Hikasa ……  547
318 Effects of the grain size and volume fraction of second hard phase on mechanical properties of DP steel D.Kondo ……  548
319 (Nishiyama Commemorative Prize)
Development of steel sheets for can and forming process 		K.Shimizu ……  549
320 The effect of various annealing temperatures on mechanical properties and microstructures of dual phase steel sheets D.O.Kim ……  550
321 transformation texture formation at cold-rolled ultra low carbon steel surfaces N.Yoshinaga ……  551
322 Relation between grain size and plastic anisotropy of low-carbon steel strips P.G.Xu ……  552
323 Microstructure of IF steel deformed by biaxial tension Y.Ikematsu ……  553
324 (ISIJ research promotion grant)
Delayed fracture strength of 1000-1800MPa grade ultra high strength low alloy TRIP-aided steels 		T.Hojo ……  554
325 (ISIJ research promotion grant)
Microstructure and tensile properties of C-Si-Mn-Nb-Mo TRIP-aided steels with bainitic ferrite matrix 		T.Muramatsu ……  555
326 Shape-fixability mechanism of hot forming and die quench K.Kusumi ……  556
327 Property of press quenched zinc plated steel sheet K.Imai ……  557
328 (Shiraishi Commemorative Prize)
A study on evaluation of environmentally assisted  fracture of steels 		J.Kobayashi
329 The effect of relative humidity on delayed fracture behavior of high strength bolt steels under atmospheric corrosion condition K.Matsukado ……  558
330 Effects of drawing strain and aging temperature on hydrogen absorption in high carbon steel wires T.Chida ……  559
331 Hydrogen environment degradation properties of FCC metals hydrogen-charged
by electrolysis and high-pressure 		K.Murakami ……  560
332 Hydrogen absorption and degradation susceptibility of cold-drawn high-strength stainless steel wire Y.Honda ……  561
333 Strain-aging properties of high strength linepipe steels Y.Shinohara ……  562
334 Effect of yield point elongation and shape irregularity on strain capacity of line pipe E.Tsuru ……  563
335 Microstructural features affecting SSC properties of 125ksi grade high strength low alloy steel OCTG T.Omura ……  564
336 Effect of Mn on the austenite grain growth property K.Hashimoto ……  565
337 Influence of micro-shot peening on surface layer characteristics Y.Harada ……  566
338 Bendability of medium carbon steel sheets with sheared edge M.Suzuki ……  567
339 Investigation of fiber reinforced metal for hot tool materials S.Uchida ……  568
340 Observation of machined surface in pure iron and S10C
(Study on creation mechanism of machined surface in low carbon steel-1) 		M.Hashimura ……  569
341 Observation of machined surface in low carbon free machining steel
(Study on creation mechanism of machined surface in low carbon steel-2) 		M.Hashimura ……  570
342 Wear reduction of carbide tools observed in Ti-added low carbon free cutting steels N.Matsui ……  571
343 Three-dimensional atom probe analysis of high carbon steel wires by FIB microsampling method J.Takahashi ……  572
344 Effect of microstructural features on ductility of drawn pearlitic carbon steels Won Jong Nam ……  573
345 (Shiraishi Commemorative Prize)
Corrosion testing by using new atomospheric corrosion test device 		H.Masuda
346 (Satomi Prize)
Effects of environment factors on atmospheric corrosion behavior of steels 		T.Shinohara
347 Corrosion and water wettability under NaF solution of Ti and Ti alloy K.Mukai ……  574
348 (ISIJ research promotion grant)
Initial stage of localized corrosion in micro-pit formed by photon rupture on zinc alloy coated steels 		M.Sakairi ……  575
349 (Nishiyama Commemorative Prize)
Prediction of application limits of passive alloys for environment-induced degradation(E.I.D) 		A.Miyasaka ……  576
350 (Nishiyama Commemorative Prize)
Semiconductor properties of oxide films on steels and related corrosion behavior 		S.Fujimoto ……  577
351 Effects of low alloying on corrosion behavior of low carbon steel
and its welded joints in hydrochloric acid aqueous solution 		A.Usami ……  578
352 Development of corrosion resistant steel tube for sulfuric/hydrochloric acid dew-point corrosion A.Soeno ……  579
353 (Nishiyama Commemorative Prize)
Development of galvannealed steel sheet for automotive applications 		C.Kato ……  580
354 Effect of surface condition on galvanizability of Si-Mn steels T.Yasui ……  581
355 Properties of chromate-free aluminized steel S.Yamaguchi ……  582
356 Properties of Non-Chromated Tin-Zinc plated steel sheets for automotive fuel tanks Y.Goto ……  583
357 (Nishiyama Commemorative Prize)
Application of dry coating process for surface treatment steel sheets 		M.Saito ……  584
358 Effect of additives on Zn-Cr alloy electrodeposition K.Matsumura ……  585
359 Electrochemical analysis of the organic additive's role on the Zn-Cr alloy electrodeposition M.Kurosaki ……  586
360 Mg effect for perforation corrosion behavior of inoganic composite coated steel sheet K.Hayashi ……  587
361 (ISIJ research promotion grant)
Preparation of stainless steel surface having a high resistance to water vapor oxidation by the molten salt electrodeposition 		M.Fukumoto ……  588
362 Observation of strain induced martensite in austenitic stainless steel by EBSP T.Mizoguchi ……  589
363 Effect of surface grinding on microstructure and hardness of high nitrogen austenitic stainless steel fabricated by nitrogen absorption method H.Tentaku ……  590
364 Effect of reversed austenite on work-hardening behavior in a low carbon 13% chromium martensitic stainless steel N.Nakada ……  591
365 Effects of additional elements and N2 gas pressure on microstructure and mechanical properties of Ni-free stainless steel fabricated by MA method R.Yamamoto ……  592
366 Dynamic recrystallization and grain refinement of martensite steels Y.Z.Bao ……  593
367 Effect of wire diameter and grain size on tensile properties of as-drawn austenitic stainless steel wire T.Fukumaru ……  594
368 Microstructure and mechanical properties of ferritic stainless steel thin wire fabricated from mechanically alloyed powder T.Onomoto ……  595
369 Evaluation of materials properties using mechanical testing facilities in gaseous hydrogen at up to 45MPa
Mechanical properties of liner materials for 35MPa-class on-board hydrogen fuel tanks in fuel cell vihcles-1 		S.Ohmiya ……  596
370 Fatigue properties of SUS316L and A6061-T6 liner materials in 45MPa gaseous hydrogen
Mechanical properties of liner materials for 35MPa-class on-board hydrogen fuel tanks in fuel cell vihcles-2 		S.Ohmiya ……  597
371 Effect of work hardening on bulging formability in austenitic stainless steel E.Ishimaru ……  598
372 Effect of mechanical properties on fine blanking of metastable austenitic stainless steel H.Tanaka ……  599
373 Effect of S and Ti on machinability of PH stainless steel SUS630 K.Nakama ……  600
374 Resistance to high temperature fatigue settling for high strength stainless steel S.Isozaki ……  601
375 Effect of Cr on initial rust resistance of the cut-edge in ferritic steels S.Okada ……  602
376 Effect of Ni on crevice corrosion behavior for 18Cr stainless steel T.Watanabe ……  603
377 Effect of dilution on corrosion resistance of super austenitic stainless steel weld joint R.Honma ……  604
378 Effects of stress and microstructures on SCC susceptibility of austenite stainless steels N.Yoneyama ……  605
379 Oxidation behavior of Al containing ferritic stainless steel in an exhaust gas atmosphere Y.Inoue ……  606
380 Effects of alloy elements on properties in Cr-Mn-Ni austenitic stainless steels T.Oshima ……  607
381 (Nishiyama Commemorative Prize)
Large strain-high Z deformation and fabrication of ultrafine-grained steel bar and plate 		S.Torizuka ……  608
382 to transformation behavior under rapid reheating.
-Mechanism of abnormal to transformation(3)- 		T.Hara ……  609
383 In-situ observation of to   transformation by scanning ion microscopy
-Mechanism of abnormal to transformation (4)- 		M.Sugiyama ……  610
384 Effect of cooling rates on microstructure evolution of rapidly-cooled high-impurity steels Hansoo Kim ……  611
385 Variant selection of upper bainite formed at austenite grain boundary T.Furuhara ……  612
386 Ultrafine TRIP-aided multi-phase steels M.Wakita ……  613
387 Phase separation of spherical B2 precipitates in Fe-Al-Ni alloy Y.Tomimasu ……  614
388 Dissolution of cementite in steels by heavy deformation and microstructural changes after heating Y.Todaka ……  615
389 (Asada Medal)
Induction hardening and tempering  as a metamorphosing technique of steel products 		K.Kawasaki
390 (ISIJ research promotion grant)
Effects of MnS on formation of bainite in steels 		N.Kanno ……  616
391 Effect of size and shape of MnS in steel on drill machinability K.Miyanishi ……  617
392 Effect of TMCP conditions on second phase morphology and precipitation behavior in low-carbon microalloyed steels T.Shinmiya ……  618
393 Microstructure of plasma nitrided Fe-Cr alloys G.Miyamoto ……  619
394 Refinement dispersion of cementite in high strength steels by rapid heating tempering-1 A.Nagao ……  620
395 Effect of prior deformation in recrystallization behavior of ultralow carbon martensitic steel M.Natori ……  621
396 Effect of carbon on work hardening behavior in 18%Ni martensitic steel K.Nakashima ……  622
397 Estimation of dislocation strengthening in cold-worked ultralow carbon 18%Ni martensitic steel Y.Fujimura ……  623


Process Evaluation and Material Characterization

398 (ISIJ research promotion grant)
Chemical information analysis of coals by using infrared and near infrared spectroscopy 		M.Kaihara ……  652
399 Development of real time monitoring instrument for trace gas analysis based on Jet-REMPI technique -Development of high sensitive daly detector- S.Hayashi ……  653
400 Elemental mapping by micro X-ray fluorescence instrument using polycapillary X-ray lens K.Tsuji ……  654
401 Surface analysis using STM in the process of reducing iron oxides T.Yamashita ……  655
402 (Nishiyama Commemorative Prize)
Characterization of surface films on materials -Measurement of transport numbers of ions in electrodeposited oxide films 		Y.Yomura ……  656
403 (ISIJ research promotion grant)
Analytical conditions for quantitative analysis of lead in steels in glow discharge optical emission spectrometry 		K.Wagatsuma ……  657
404 Determination of trace amounts of Cu,Ni,Ti and B in Fe-based alloys by radio-frequency-powered glow discharge optical emission spectrometry associated with bias-current conduction method T.Fujimura ……  658
405 High speed observation of Spark discharge emission process K.Mizukami ……  659
406 The development of determination technique with high precision for precipitates existing in the surface of the steel M.Inose ……  660
407 Distribution profiles of boron near copper-iron boundaries by laser ablation-sector field inductively coupled plasma mass spectrometry M.Uemoto ……  661
408 Determination of trace amounts of mercury, lead, and cadmium by ICP-MS after ion-exchange chromatographic separation K.Fujimoto ……  662
409 Analysis of trace amounts of sulfur in steel by ICP-MS using mini column with activated aluminium oxide H.Koga ……  663


ISIJ and JIM Joint Session
Microstructure and Properties of Materials

J1 Effects of B addition and aging on mechanical properties of TiNbAl alloys Y.Horiuchi ……  686
J2 Cold work properties of -Zr and Ti alloys M.Sakisaka ……  686
J3 Influence of Sc addition on microstructure and mechanical prorerties of Ti-6-mol%Mo alloy Y.Iwanaga ……  687
J4 Direct reduction of TiO2 using molten salt electrolysis with solid electrolyte ZrO2 R.Suzuki ……  688
J5 Fabrication of fine-grained -type titanium alloy through mechanical alloying treatment S.Hamamoto ……  689
J6 (ISIJ research promotion grant)
Effects of the heating temperature and time on grain growth in + type titanium alloy containing a small amount of yttrium 		S.Hotta ……  690
J7 Influence of solid solution hydrogen on grain growth in commercially pure titanium H.Fujii ……  691
J8 Characterization of deformation behaviors of Ti-Nb-Ta-Zr system alloys using X-ray diffraction analysis N.Sakaguchi ……  692
J9 Effect of alloying elements on phase constitution and heat treatment behaviour of Ti-Nb-Ta-Zr alloys for biomedical applications M.Ikeda ……  692
J10 Evaluation of discoloration resistance of vacuum annealed (VA) architectural titanium sheets newly developed in long term atmospheric exposure tests M.Kaneko ……  693
J11 Change in microstruture and hardness of titanium with nitrogen absorption in single phase region T.Andou ……  694
J12 In-situ synthesis of titanium base composite dispersed with Ti_{5}Si_{3} particles via solid reaction started from elemental mixture of titanium and glass scraps M.Sumida ……  694
J13 Improvement of creep resistance in nano-sized TiB particle reinforced Ti2AlNb composites M.Hagiwara ……  695
J14 High-cycle fatigue fracture in alpha-titanium Y.Shindo ……  696
J15 Thermally or stress induced martensite transformation in Ti-10V-2Fe-3Al with nitrogen addition T.Furuhara ……  696
J16 Development of ultra steel screw S.Torizuka ……  697
J17 Grain refinement mechanisms due to super short interval multi-pass rolling in stable austenite region K.Miyata ……  698
J18 Deformation microstructures in cold-rolled Fe-36mass%Ni alloy T.Morikawa ……  698
J19 Grain refinement of Mg alloy by torsion extrusion
 		S.Mizunuma ……  699
J20 Mechanism of strain rate dependent deformation at ambient temperature in ultrafine grained aluminum N.Tsuji ……  700
J21 Correlation between ultrafine structure and strength of ARB processed and annealed high purity aluminum N.Kamikawa ……  700
J22 TEM/3DAP characterization of cold drawn Cu-Ag-Nb wire S.Ohsaki ……  701
J23 Internal stress field in ultrafine grained aluminium measured by TEM/CBED R.Ueji ……  701
J24 Microstructure change during warm deformation in high carbon steels T.Maki ……  702
J25 Microstructure and high temperature deformation of nano-grained tungsten E.Oda ……  703
J26 Dependence of the relationship between intergranular and intragranular deformation of nanocrystalline metals on grain size by molecular dynamics simulations T.Shimokawa ……  703
J27 Effect of nitrogen on Hall-Petch coefficient in austenitic steel T.Tsuchiyama ……  704
J28 Severe vibration straining process (SVSP) for rapid continuous grain refinement of sheet metals K.Nakamura ……  705
J29 Microstructure control of magnesium alloys by severe torsion straining process Y.Miyahara ……  705
J30 Factors of grain refinement for Al-Mg alloy fabricated Sever Torsion Strain Process K.Neishi ……  706
J31 Microstructure control of Fe-C steel by Severe Torsion Straining Process Y.Kawasaki ……  706
J32 Effect of strain gradient on the formation of nanocrystalline structure M.Umemoto ……  707
J33 (ISIJ research promotion grant)
Drilling conditions to form nanocrystalline structure in steels by drilling 		Y.Todaka ……  708
J34 Grain refinement and thermal stability of FCC metals by ECAP K.Kishikawa ……  709
J35 Effect of cold rolling on plate sample processed by ECAP Y.Hisatsune ……  709
J36 Microstructure and mechanical properties of an SUS316L and a Ti-6Al-4V HRS materials H.Fujiwara ……  710
J37 Dynamic recrystallization of ferrite during large strain warm compression
of ultra-low carbon steel 		S.V.S. Narayana Murty ……  710

previous page